View source for Installing an Axis P5514/P5515 with a Louroe Verifact A

==Required Parts And Tools==

* Axis P5514 or P5515 
* Louroe IFPX 
* 3.5mm (Male to Male) Audio Cable 
* Louroe Verifact A Microphone 
* P55/Q60 I/O Multi-Connector                       
* S2 T10 Torx security bit
* Wire Stripper    
* Wall Dog Screw Anchor 
* Toggle Bolts (If mounting to drop ceiling tile) 
* Drill bit and drill 
* Phillips head drill bit or Phillips head screwdriver
* Small Flat head screwdriver  
* Cat5/6 Patch Cable (7ft-15ft recommended)  
* Shielded Stranded 22/2 + ground Wire 
* Razor / box cutter

==Installation Instructions==

#Locate the network drop above the ceiling either being a male Ethernet end (service loop) or a biscuit jack. This will have been ran back to the POE switch. If the switch does not have POE, a POE injector will need to be installed at the network closet.
#Using a set of wall dog screws, mount the Louroe IFPX above into the drywall above the drop ceiling. (Note, if no drop ceiling make other arrangements to mount the IFPX.)
#Connect the network drop into the RJ-45 (f) on the IFPX that reads '''Power+Data In'''. When connected, you should see activity on the link lights. If no link lights appear, ensure that POE is enabled on your POE switch, and that the network drop is plugged in.
#Using the instructions included in the P5514/P5515 box, use the razor to cut a hole into the drop ceiling tile, assemble the holding bracket for the camera, and mount the bracket to drop ceiling.
#:[[File:P5515BracketAssembled.JPG|500x400px|link=https://ipivs.com/wiki/images/b/bd/P5515BracketAssembled.JPG]]
#Using the CAT5/6 patch cable, connect the camera to the RJ-45 (f) on the IFPX labeled '''Power+Data Out'''. Ensure that you’ve ran this cable through the opening at the top of the camera mounting bracket.
#Run the Axis P55/Q60 Multi-Connector cable through the top opening of the camera mounting bracket, connecting the end into the I/O connector on the camera (See Pictures).
#:[[File:P5515OpenedUp.JPG|400x300px|link=https://ipivs.com/wiki/images/5/57/P5515OpenedUp.JPG]][[File:P5515WiredUp.JPG|400x300px|link=https://ipivs.com/wiki/images/c/ca/P5515WiredUp.JPG]][[File:P5515WiredAndClosed.JPG|400x300px|link=https://ipivs.com/wiki/images/6/6e/P5515WiredAndClosed.JPG]]

==Connecting the Microphone==
# Take the 3.5mm Male to Male audio cable and connect it from the 3.5mm jack labeled '''AUDIO OUT''' on the IFPX, into the pink “AUDIO IN” on the P55/Q60 I/O Connector.
#:[[File:IFPXwiredP55Q60.JPG|400x300px|link=https://ipivs.com/wiki/images/a/ab/IFPXwiredP55Q60.JPG]]
#Strip the jacket off the 22/2, revealing the red, black, and common (bare wire) on both sides of the cable. Remove the string and plastic casings covering the red and black cables. Strip the red and black jackets off the wire exposing the copper. Cut copper evenly on both ends (See picture)
#:[[File:Stripped_22_2_Wire.JPG|400x300px|link=https://ipivs.com/wiki/images/5/57/Stripped_22_2_Wire.JPG]]
#Drill a hole into the piece of ceiling tile that you will be mounting the Louroe Verifact-A onto. Feed one end of the the 22/2 audio cable through the hole. Connect the audio cable to the Verifact-A Phoenix terminal as follows; Red to A, Black to B, Common (bare wire) to C (See Picture)
#:[[File:Wired_Verifact_A.JPG|400x300px|link=https://ipivs.com/wiki/images/4/4e/Wired_Verifact_A.JPG]]
#Connect the other end of your 22/2 cable to  the terminal on the IFPX labeled '''MIC/SPEAKER A B C SP'''. The connections will be as follows; Red to A, Black to B, Common (bare wire) to C (See Picture)
#:[[File:Wired_up_IFPX.JPG|400x300px|link=https://ipivs.com/wiki/images/8/86/Wired_up_IFPX.JPG]]
#Place the camera into the ceiling and secure it to the bracket. Use the included safety cable to attach the camera to the bracket. Hide excess cable in the ceiling. Cover mounting hardware by snapping Axis plate into place around the dome
[[File:Mounted P5515.JPG|400x300px|link=https://ipivs.com/wiki/images/7/7f/Mounted_P5515.JPG]]