IVSWikiBlue at 20:42, 24 March 2025

2025-03-24T20:42:22Z

IVSWikiBlue at 16:18, 10 October 2023

2023-10-10T16:18:30Z

IVSWikiBlue: Created page with "
The following camera settings should be enabled prior to adding the camera to the VALT system.

1) Browse to the camera..."

2023-08-03T20:13:20Z

Created page with "<div class="floating_card">The following camera settings should be enabled prior to adding the camera to the VALT system.</div> <div class="section"> 1) Browse to the camera..."

New page

<div class="floating_card">The following camera settings should be enabled prior to adding the camera to the VALT system.</div>

<div class="section">
1) Browse to the camera address (you can find the camera address using the Axis IP Utility application), and set the '''root''' password.

{{img | file = 100.jpg | width = 800px}}

2) Click on the '''Setup''' link in the upper left corner, then go to '''Basic Setup''' -> '''Video Stream''' make sure '''Compression''' is set to 30 and '''Frame Rate''' is set to 30.

{{img | file = 140.jpg | width = 800px}}

3) Click on the '''H.264''' tab and change the '''GOP Length''' to 20.

{{img | file = P5414-E_GopLength.png | width = 800px}}

4) Click on the '''Audio''' tab. Check the '''Enable Audio''' checkbox (ensure the audio format is set to '''AAC''') as shown below then press Save.

{{img | file = 141.jpg | width = 800px}}

5) Click on the '''Audio Settings''' section (using Chrome) and ensure a signal is present, using the audio indicator. When no one is speaking audio should be '''-40''' to '''-30 db''', and when someone is speaking, audio should be '''-20''' to '''-5 db'''.

{{img | file = 155.jpg | width = 800px}}

6) For proper I/O and Talkback functionality when using cameras with Axis firmware version 5.70 or greater:

Under '''Settings''' --> '''System Options''' --> '''Security''' --> '''Users''' you will need to set '''Allow Password''' type to '''Unencrypted Only''', as shown below.

After this change, you will need to restart the camera.

{{img | file = 5514.jpg | width = 800px}}

7) For proper I/O and Talkback functionality when using cameras with Axis firmware version 8.0 or greater:

Under '''Settings''' --> '''Plain Config''' --> '''Network''' --> you will need to set '''Authentication policy''' to '''Basic''', as shown below.

{{img | file = Basicpolicy.PNG | width = 800px}}
</div>

← Older revision		Revision as of 20:42, 24 March 2025
Line 36:		Line 36:
	{{img \| file = Basicpolicy.PNG \| width = 800px}}		{{img \| file = Basicpolicy.PNG \| width = 800px}}
	}}		}}
		+	[[Category:Cameras]]

@@ Line 1: / Line 1: @@
 <div class="floating_card">The following camera settings should be enabled prior to adding the camera to the VALT system.</div>
 ) Browse to the camera address (you can find the camera address using the Axis IP Utility application), and set the '''root''' password.
@@ Line 35: / Line 35: @@
 {{img | file = Basicpolicy.PNG | width = 800px}}
-</div>
+}}

Camera Settings Older Firmware - Revision history

IVSWikiBlue at 20:42, 24 March 2025

IVSWikiBlue at 16:18, 10 October 2023

IVSWikiBlue: Created page with "The following camera settings should be enabled prior to adding the camera to the VALT system. 1) Browse to the camera..."

IVSWikiBlue: Created page with "
The following camera settings should be enabled prior to adding the camera to the VALT system.

1) Browse to the camera..."