Control Room Audio Solution - Revision history

IVSWikiBlue: /* Tesira Software */

2022-05-10T15:30:12Z

‎Tesira Software

IVSWikiBlue: /* Physical Wiring/Line Diagram */

2022-05-10T15:22:30Z

‎Physical Wiring/Line Diagram

IVSWikiBlue: /* AEC Block */

2020-11-16T16:55:00Z

‎AEC Block

IVSWikiBlue at 15:56, 20 May 2020

2020-05-20T15:56:53Z

IVSWikiBlue at 20:28, 5 May 2020

2020-05-05T20:28:51Z

IVSWikiBlue: /* Connections */

2020-04-29T19:08:12Z

‎Connections

IVSWikiBlue at 18:24, 27 April 2020

2020-04-27T18:24:43Z

IVSWikiBlue: /* Processing Blocks in Tesira */

2020-04-27T17:59:14Z

‎Processing Blocks in Tesira

IVSWikiBlue at 18:24, 24 April 2020

2020-04-24T18:24:26Z

IVSWikiBlue at 18:08, 24 April 2020

2020-04-24T18:08:26Z

@@ Line 37: / Line 37: @@
 When this is complete, the file should look something like this:
-[[File:CRAS_Config_2.png|link=]]
+{{img | file = CRAS_Config_2.png}}
 ==AEC Block==
-[[File:CRAS_with_Input_Blocks.png|link=]]
+{{img | file = CRAS_with_Input_Blocks.png}}
 #Phantom Power: The mics will need phantom power, and proper levels on the preamps. Use the peak meter to gauge the audio levels so that optimal dialog peaks between -12 and 6 dB.
@@ Line 50: / Line 50: @@
 AEC is important, and sometimes difficult to understand. There is a separate section on how to configure AEC. Click the image below to read up on AEC:
-[[File:AEC.png|link=https://ipivs.com/wiki/Acoustic_Echo_Cancellation]]
+{{img | file = AEC.png}}
@@ Line 59: / Line 59: @@
 For further insight about the other processing blocks and settings, refer back to the first configuration example, or click the image below:
-[[File:Processing_Blocks_Page.png|link=https://ipivs.com/wiki/Simple_Configuration#Processing_Blocks_in_Tesira]]
+{{img | file = Processing_Blocks_Page.png}}
 ==EQ and Compression==
 For information on EQ settings, or click the image below:
-[[File:EQ_Page.png|link=https://ipivs.com/wiki/EQ_Processing]]
+{{img | file = EQ_Page.png}}
 For Compression parameters, click the image below:
-[[File:Compression_Page.png|link=https://ipivs.com/wiki/Compression_Settings]]
+{{img | file = Compression_Page.png}}

← Older revision		Revision as of 15:22, 10 May 2022
Line 12:		Line 12:


−	~~[[File:CRAS_Line_Diagram.png~~\|~~link~~=~~https://ipivs.com/wiki/images/2/2e/~~CRAS_Line_Diagram.png\|500px]]	+	{{img \| file = CRAS_Line_Diagram.png \| width=500px}}

	=Tesira Software=		=Tesira Software=

@@ Line 43: / Line 43: @@
 [[File:CRAS_with_Input_Blocks.png|link=]]
-#Phantom Power: The mics will need phantom power, and proper levels on the preamps.
+#Phantom Power: The mics will need phantom power, and proper levels on the preamps. Use the peak meter to gauge the audio levels so that optimal dialog peaks between -12 and 6 dB.
 #AEC: For the first time in the example configurations, Acoustic Echo Cancellation will be used. The reason for this is: anytime there is a microphone and a talkback speaker in the same room, there is the opportunity for an echo and/or feedback. AEC will cancel the delayed audio or feedback. Enable the AEC feature with this button on the AEC Block. AEC is explored in depth in another section.
 ==Acoustic Echo Cancellation==

@@ Line 37: / Line 37: @@
 When this is complete, the file should look something like this:
-[[File:CRAS_Config_2.png]]
+[[File:CRAS_Config_2.png|link=]]
 ==AEC Block==
-[[File:CRAS_with_Input_Blocks.png]]
+[[File:CRAS_with_Input_Blocks.png|link=]]
 #Phantom Power: The mics will need phantom power, and proper levels on the preamps.

@@ Line 1: / Line 1: @@
 =Description/Objective=
-In this example, we will be building 1 sim rooms with an overhead speaker and 1 observation room with live audio and a talkback microphone. For physical devices, we will have 1 room microphone, 1 camera, 1 OWISP, and 1 PSP speaker (and/or SHM-1 headphone amp).
+In this example, we will be building 1 sim rooms with an overhead speaker and 1 observation room with live audio and a talkback microphone. For physical devices, there will be 1 room microphone, 1 camera, 1 OWISP, and 1 PSP speaker (and/or SHM-1 headphone amp).
 =Physical Wiring/Line Diagram=
-We will need 2 inputs and 3 outputs. The inputs and outputs should be as follows:
+inputs and 3 outputs will be needed. The inputs and outputs should be as follows:
 #* Input 1: Sim Room Mic
 #* Input 2: Control Room Talkback Mic
@@ Line 17: / Line 17: @@
 ==Connections==
-# Once we've completed our physical connections, open the Tesira software and build a configuration.
+# If the physical connections are complete, open the Tesira software and start building a configuration.
-# In this configuration we'll be using the following blocks. Add these blocks to the configuration:
+# In this configuration use the following blocks:
 #* TesiraFORTE CI block ("per channel" AEC reference mode)
 #* Peak Meter x 3
@@ Line 26: / Line 26: @@
 #* Matrix Mixer with at least 2 inputs and 3 outputs, with 2 extra outputs
 #Connect the blocks as follows:
-#* The Tesira Input block will already be connected to the AEC block, so connect the first peak meter to the Input block also. This will help us to be sure we have the proper levels set on the preamp.
+#* The Tesira Input block will already be connected to the AEC block, so connect the first peak meter to the Input block also. This will help ensure proper levels are set on the preamp.
 #* Connect the AEC block to the Uber Filters.
 #* Send the Uber Filters to the Level Block.
 #* Send the Level Block to the Compressor and the second peak meter.
 #* Send the Compressor to the Matrix Mixer.
-#* Connect output 1-3 from the mixer to port 1-3 on the Tesira Output block AND to the third peak meter. This way we can make sure to reach the right audio levels before we send it to the cameras.
+#* Connect output 1-3 from the mixer to port 1-3 on the Tesira Output block AND to the third peak meter. This will ensure the right audio levels are sent to the camera.
 #* Connect the 2 extra outputs from the Matrix Mixer to ports 1&2 on the AEC reference.
-When we're complete, our file should look something like this:
+When this is complete, the file should look something like this:
 [[File:CRAS_Config_2.png]]
@@ Line 43: / Line 43: @@
 [[File:CRAS_with_Input_Blocks.png]]
-#Phantom Power: We will need phantom power on for our mics, and proper levels on the preamps.
+#Phantom Power: The mics will need phantom power, and proper levels on the preamps.
-#AEC: For the first time in our example configurations, we are going to use Acoustic Echo Cancellation. The reason for this is: anytime we have a microphone and a talkback speaker in the same room, there is the opportunity for an echo and/or feedback. AEC will help us cancel the delayed audio or feedback. Enable the AEC feature with this button on the AEC Block. We will explore AEC in depth in another section.
+#AEC: For the first time in the example configurations, Acoustic Echo Cancellation will be used. The reason for this is: anytime there is a microphone and a talkback speaker in the same room, there is the opportunity for an echo and/or feedback. AEC will cancel the delayed audio or feedback. Enable the AEC feature with this button on the AEC Block. AEC is explored in depth in another section.

← Older revision		Revision as of 19:08, 29 April 2020
Line 38:		Line 38:

	[[File:CRAS_Config_2.png]]		[[File:CRAS_Config_2.png]]
−
−
−

	==AEC Block==		==AEC Block==

@@ Line 67: / Line 67: @@
 ==EQ and Compression==
-For information on EQ settings and compression, refer to Simple Configuration with EQ and Compression, or click the image below:
+For information on EQ settings, or click the image below:
-[[File:One_Complex_Config.png|link=https://ipivs.com/wiki/Simple_Configuration_with_EQ_and_Compression#Processing_Blocks_in_Tesira]]

← Older revision		Revision as of 18:08, 24 April 2020
Line 42:		Line 42:


−	==Matrix Mixer ~~for ORAS with Software Talkback~~==	+	==AEC Block==
		+
		+	[[File:CRAS_with_Input_Blocks.png]]
		+
		+	#Phantom Power: We will need phantom power on for our mics, and proper levels on the preamps.
		+	#AEC: For the first time in our example configurations, we are going to use Acoustic Echo Cancellation. The reason for this is: anytime we have a microphone and a talkback speaker in the same room, there is the opportunity for an echo and/or feedback. AEC will help us cancel the delayed audio or feedback. Enable the AEC feature with this button on the AEC Block.
		+
		+
		+	==How to Use the Mixer with AEC==
		+
		+	There are 2 ways to configure the Matrix Mixer to use AEC properly. We will explore those options here. They are functionally the same, but you may find one method to be conceptually easier to use.
		+
		+
		+	===Method 1===
		+
		+
		+	===Method 2===

−	~~[[File:ORAS_with_Software_Talkback_Blocks_2.png]]~~

−	~~#Phantom Power: We will need phantom power on for our room mics, and proper levels on the preamps.~~
−	#AEC: For the first time in our example configurations, we are going to use Acoustic Echo Cancellation. The reason for this is: anytime we have a microphone and a talkback speaker in the same room, there is the opportunity for an echo. If John is in the control room using the software to talk to Steve, who is in the simulation room, the room mic will pick up John's voice from the OWISP, and John will once again hear his own voice in the control room with a short delay. AEC will help us cancel this delayed audio. Enable the AEC feature with this button on the AEC Block.
−	~~#Output Channels: 3A highlights the output channels to the devices for the first pair of ORAS rooms; 3B indicates the devices for the second pair; and 3C highlights the AEC reference channels.~~


Line 63:		Line 75:

	[[File:One_Complex_Config.png\|link=https://ipivs.com/wiki/Simple_Configuration_with_EQ_and_Compression#Processing_Blocks_in_Tesira]]		[[File:One_Complex_Config.png\|link=https://ipivs.com/wiki/Simple_Configuration_with_EQ_and_Compression#Processing_Blocks_in_Tesira]]
−
−
−	~~=How AEC Works=~~
−
−
−	~~[[File:ORAS_with_Software_Talkback_AEC2.png]]~~
−
−	~~John is in the observation room, using the talkback feature. His audio is what's in danger of being captured and returned to him~~