RDL ST-VOX1 - Revision history

IVSWikiBlue: /* Data Sheet */

2022-05-09T21:35:49Z

‎Data Sheet

2022-02-09T20:55:08Z

‎How to Wire

2021-09-14T20:10:02Z

‎Data Sheet

2021-09-14T20:09:50Z

‎Data Sheet

2021-09-14T20:09:42Z

‎How to Wire

2021-09-14T20:09:08Z

‎How to Wire

2021-04-28T15:59:04Z

2021-04-28T15:56:42Z

2021-04-28T15:53:46Z

2021-04-28T15:49:33Z

← Older revision		Revision as of 21:35, 9 May 2022
Line 27:		Line 27:
	== Data Sheet ==		== Data Sheet ==

−	~~[[File:ST-VOX1.png~~\|~~link~~=~~https://wiki.ipivs.com/wiki/images/b/bc/~~ST-VOX1.png]]	+	{{img \| file = ST-VOX1.png}}

@@ Line 22: / Line 22: @@
 Adjust sensitivity and delay as needed; 25 turns sets to max of 5 seconds.
 == Data Sheet ==
 [[File:ST-VOX1.png|link=https://wiki.ipivs.com/wiki/images/b/bc/ST-VOX1.png]]

← Older revision		Revision as of 20:10, 14 September 2021
Line 25:		Line 25:
	== Data Sheet ==		== Data Sheet ==

−	[[File:ST-VOX1.png\|https://wiki.ipivs.com/wiki/images/b/bc/ST-VOX1.png]]	+	[[File:ST-VOX1.png\|link=https://wiki.ipivs.com/wiki/images/b/bc/ST-VOX1.png]]

← Older revision		Revision as of 20:09, 14 September 2021
Line 25:		Line 25:
	== Data Sheet ==		== Data Sheet ==

−	[[File:ST-VOX1.png\|https://ipivs.com/wiki/images/b/bc/ST-VOX1.png]]	+	[[File:ST-VOX1.png\|https://wiki.ipivs.com/wiki/images/b/bc/ST-VOX1.png]]

@@ Line 2: / Line 2: @@
 == How to Wire ==
-[[File:STVOX1Diagram.png|500px|thumb|right|The red line corresponds to your STM-1's output.  The yellow line corresponds to your output line.  The Green line corresponds to your second input.]]
+[[File:STVOX1Diagram.png|500px|thumb|right|The red line corresponds to your STM-1's output.  The yellow line corresponds to your output line.  The Green line corresponds to your second input.|link=]]
 Set up microphone and STM-1 as usual, but send HI-Z Audio out to the VOX input line.

← Older revision		Revision as of 15:53, 28 April 2021
Line 2:		Line 2:
	== How to Wire ==		== How to Wire ==

		+	[[File:STVOX1Diagram.png]]

	Set up microphone and STM-1 as usual, but send HI-Z Audio out to the VOX input line.		Set up microphone and STM-1 as usual, but send HI-Z Audio out to the VOX input line.

← Older revision		Revision as of 15:49, 28 April 2021
Line 1:		Line 1:
		+
		+	== How to Wire ==
		+
		+
		+	Set up microphone and STM-1 as usual, but send HI-Z Audio out to the VOX input line.
		+
		+	Connect audio line to positive on VOX, leave ground out for future b-connecting or terminal block connection.
		+
		+	Insert jumper wire connecting the audio input line to the final dot on the first collection of dots and lines, the first relay circuit. This allows the observation microphone in this case to be used as the alternative source
		+	for when the VOX fires off while it is being used.
		+
		+	Connect power, no jumpers and in it’s own dedicated ground slot.
		+
		+	Skip the slave terminal, unless you have another relay to connect to.
		+
		+	On the first dot, the first slot of the relay, insert your output’s audio line, leaving the ground for the line out for, once again, future grounding.
		+
		+	You’ll repeat the same process for the next slot in the relay, except with your second audio source.
		+
		+	Connect all grounds with your preferred method, and connect to ground next to input
		+
		+	Adjust sensitivity and delay as needed; 25 turns sets to max of 5 seconds.
		+
		+
		+
		+
		+
		+	== Data Sheet ==
		+
	[[File:ST-VOX1.png\|https://ipivs.com/wiki/images/b/bc/ST-VOX1.png]]		[[File:ST-VOX1.png\|https://ipivs.com/wiki/images/b/bc/ST-VOX1.png]]