Template:Connecting The Microphone Shure MX202i STM1 - Revision history

IVSWikiBlue: /* Connecting and Mounting the Microphone */

2022-08-02T17:46:24Z

‎Connecting and Mounting the Microphone

IVSWikiBlue: /* Connecting the STM-1 */

2022-08-02T17:46:11Z

‎Connecting the STM-1

IVSWikiBlue: /* Connecting and Mounting the Microphone */

2022-05-10T14:59:45Z

‎Connecting and Mounting the Microphone

IVSWikiBlue: /* Connecting the STM-1 */

2022-05-10T14:57:57Z

‎Connecting the STM-1

IVSWikiBlue: /* Connecting and Mounting the Microphone */

2020-08-27T13:53:31Z

‎Connecting and Mounting the Microphone

IVSWikiBlue: Created page with "==Connecting the STM-1== #Cut a short piece of 22/2 cable (approx. 1 inch). Strip the jacket and from the cable and remove all contents keeping only the red cable. On both en..."

2020-05-13T15:41:01Z

Created page with "==Connecting the STM-1== #Cut a short piece of 22/2 cable (approx. 1 inch). Strip the jacket and from the cable and remove all contents keeping only the red cable. On both en..."

New page

==Connecting the STM-1==

#Cut a short piece of 22/2 cable (approx. 1 inch). Strip the jacket and from the cable and remove all contents keeping only the red cable. On both ends of the red cable, strip off a piece of the jacket (See picture).
#:[[File:Phantom Power Jumper.JPG|400x300px|link=https://ipivs.com/wiki/images/8/87/Phantom_Power_Jumper.JPG]]
#Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
#:[[File:Phantom PWR STM.JPG|400x300px|link=https://ipivs.com/wiki/images/b/b3/Phantom_PWR_STM.JPG]]
#Connect the cable ran for power to both PWR terminals (Red to +, Black to the other terminal) of the STM-1. Connect the other side to the IO phoenix connector (Red to 2, Black to 1).
#Connect the cable ran for audio to both HI-Z OUTPUT terminals (Red to +, Black to the other terminal) of the STM-1. Connect the other side to the audio in portion of the audio phoenix connector (Red to +, Black to –).
#:[[File:Wired with power and audio.JPG|400x300px|link=https://ipivs.com/wiki/images/4/46/Wired_with_power_and_audio.JPG]]
#Using the Velcro that comes with the STM-1, attach the STM-1 to the wall above drop ceiling hidden from sight.
#The microphone will be connected via the input terminals of the STM-1 (Red to +, Black to -, ground to the ground terminal).

(NOTE; If there are 2 cameras in the room, duplicate these steps to get to the 2nd camera. HI-Z output can feed 2 cameras, but no more. If there are 2 Shure MX202i Microphones, duplicate steps. An STM-1 can power and gather audio from 2 Shure 202i mics.)

==Connecting and Mounting the Microphone==

#Asses the drop ceiling to decide best mounting placement for the MX202i. Avoid tiles adjacent to HVAC or fire safety devices.
#Drill a hole into the center of the single gang plate using the ½” paddle bit (if not prefabricated).
#Measure center of the drop ceiling tile and drill a similar hole with the ½” paddle bit.
#Align the single gang plate to the location of the microphone on the drop ceiling tile using a pair of toggle bolts.
#:[[File:Plate_Mounted_to_Ceiling.JPG|400x300px|link=https://ipivs.com/wiki/images/5/5d/Plate_Mounted_to_Ceiling.JPG]]
#Run the MX202i through the ½” hole in the ceiling tile and single gang plate with the rubber stopper to secure the microphone in place and plugging the ½” hole .
#Adjust the length of the cable of the microphone to a desirable length, hiding the remainder in the ceiling near the STM-1. Attach the windscreen to the MX202i.
#:[[File:Mx202i.jpg|link=https://ipivs.com/wiki/images/9/9d/Mx202i.jpg]]
# Run the XLR mini cable to the STM-1 location.
#Connect the connect the XLR mini to the 4 pin Male XLR adapter.
#Strip away a portion of the red and black cables inside the pigtail, revealing the copper wire inside.
#*The microphone will be connected via the input terminals of the STM-1 (Red to +, Black to -, ground to the ground terminal).
# Connect the female XLR to the Male XLR adapter

@@ Line 16: / Line 16: @@
 ==Connecting and Mounting the Microphone==
+<div class="section">
 #Asses the drop ceiling to decide best mounting placement for the MX202i. Avoid tiles adjacent to HVAC or fire safety devices.
 #Drill a hole into the center of the single gang plate using the ½” paddle bit (if not prefabricated).
@@ Line 30: / Line 30: @@
 #*The microphone will be connected via the input terminals of the STM-1 (Red to +, Black to -, ground to the ground terminal).
 # Connect the female XLR to the Male XLR adapter

@@ Line 1: / Line 1: @@
 ==Connecting the STM-1==
+<div class="section">
 #Cut a short piece of 22/2 cable (approx. 1 inch). Strip the jacket and from the cable and remove all contents keeping only the red cable. On both ends of the red cable, strip off a piece of the jacket (See picture).
 #: {{img | file = Phantom Power Jumper.JPG | width=250px}}
 #Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
-#: {{img | file = Phantom PWR STM.JPG | width=750px}}
+#: {{img | file = Phantom PWR STM.JPG | width=550px}}
 #Connect the cable ran for power to both PWR terminals (Red to +, Black to the other terminal) of the STM-1. Connect the other side to the IO phoenix connector (Red to 2, Black to 1).
 #Connect the cable ran for audio to both HI-Z OUTPUT terminals (Red to +, Black to the other terminal) of the STM-1. Connect the other side to the audio in portion of the audio phoenix connector (Red to +, Black to –).
-#: {{img | file = Wired with power and audio.JPG | width=750px}}
+#: {{img | file = Wired with power and audio.JPG | width=550px}}
 #Using the Velcro that comes with the STM-1, attach the STM-1 to the wall above drop ceiling hidden from sight.
 #The microphone will be connected via the input terminals of the STM-1 (Red to +, Black to -, ground to the ground terminal).
-(NOTE; If there are 2 cameras in the room, duplicate these steps to get to the 2nd camera. HI-Z output can feed 2 cameras, but no more. If there are 2 Shure MX202i Microphones, duplicate steps. An STM-1 can power and gather audio from 2 Shure 202i mics.)
+<i>(NOTE: If there are 2 cameras in the room, duplicate these steps to get to the 2nd camera. HI-Z output can feed 2 cameras, but no more. If there are 2 Shure MX202i Microphones, duplicate steps. An STM-1 can power and gather audio from 2 Shure 202i mics.)</i>
 ==Connecting and Mounting the Microphone==

@@ Line 20: / Line 20: @@
 #Measure center of the drop ceiling tile and drill a similar hole with the ½” paddle bit.
 #Align the single gang plate to the location of the microphone on the drop ceiling tile using a pair of toggle bolts.
-#:[[File:Plate_Mounted_to_Ceiling.JPG|400x300px|link=https://ipivs.com/wiki/images/5/5d/Plate_Mounted_to_Ceiling.JPG]]
+#: {{img | file = Plate_Mounted_to_Ceiling.JPG | width=300px}}
 #Run the MX202i through the ½” hole in the ceiling tile and single gang plate with the rubber stopper to secure the microphone in place and plugging the ½” hole .
 #Adjust the length of the cable of the microphone to a desirable length, hiding the remainder in the ceiling near the STM-1. Attach the windscreen to the MX202i.
-#:[[File:Mx202i.jpg|link=https://ipivs.com/wiki/images/9/9d/Mx202i.jpg|250px]]
+#: {{img | file = Mx202i.jpg | width=250px}}
 # Run the XLR mini cable to the STM-1 location.
 #Connect the connect the XLR mini to the 4 pin Male XLR adapter.