Template:F41 MX202i STM1 - Revision history

IVSWikiBlue: /* Connecting and Mounting the Microphone */

2022-05-10T18:58:50Z

‎Connecting and Mounting the Microphone

IVSWikiBlue: /* Connecting the STM-1 */

2022-05-10T18:52:42Z

‎Connecting the STM-1

IVSWikiBlue: /* Connecting and Mounting the Microphone */

2020-08-27T15:39:28Z

‎Connecting and Mounting the Microphone

IVSWikiBlue: Created page with "==Connecting the STM-1== #Cut a short piece of 22/2 cable (approx. 1 inch). Strip the jacket and from the cable and remove all contents keeping only the red cable. On both en..."

2020-05-13T19:13:35Z

Created page with "==Connecting the STM-1== #Cut a short piece of 22/2 cable (approx. 1 inch). Strip the jacket and from the cable and remove all contents keeping only the red cable. On both en..."

New page

==Connecting the STM-1==

#Cut a short piece of 22/2 cable (approx. 1 inch). Strip the jacket and from the cable and remove all contents keeping only the red cable. On both ends of the red cable, strip off a piece of the jacket (See picture).
#:[[File:Phantom Power Jumper.JPG|400x300px|link=https://ipivs.com/wiki/images/8/87/Phantom_Power_Jumper.JPG]]
#Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
#:[[File:Phantom PWR STM.JPG|400x300px|link=https://ipivs.com/wiki/images/b/b3/Phantom_PWR_STM.JPG]]
#Connect the cable ran for power to both PWR terminals (Red to +, Black to the other terminal) of the STM-1. Connect the other side to the IO phoenix connector (Red to 2, Black to 1).
#Connect the cable ran for audio to both LO-Z OUTPUT terminals (Red to +, Black to -, and ground to the ground terminal) of the STM-1. Connect the other end of the 3.5mm cable to the in on the F41. (cut to appropriate length between STM-1 and F41)
#:[[File:STM1F41.jpeg|400x300px|link=https://ipivs.com/wiki/images/d/dc/STM1F41.jpeg]]

==Connecting and Mounting the Microphone==

#Asses the drop ceiling to decide best mounting placement for the MX202i. Avoid tiles adjacent to HVAC or fire safety devices.
#Drill a hole into the center of the single gang plate using the ½” paddle bit (if not prefabricated).
#Measure center of the drop ceiling tile and drill a similar hole with the ½” paddle bit.
#Align the single gang plate to the location of the microphone on the drop ceiling tile using a pair of toggle bolts.
#:[[File:Plate_Mounted_to_Ceiling.JPG|400x300px|link=https://ipivs.com/wiki/images/5/5d/Plate_Mounted_to_Ceiling.JPG]]
#Run the MX202i through the ½” hole in the ceiling tile and single gang plate with the rubber stopper to secure the microphone in place and plugging the ½” hole .
#Adjust the length of the cable of the microphone to a desirable length, hiding the remainder in the ceiling near the STM-1. Attach the windscreen to the MX202i.
#:[[File:Mx202i.jpg|link=https://ipivs.com/wiki/images/9/9d/Mx202i.jpg]]
# Run the XLR mini cable to the STM-1 location.
#Connect the connect the XLR mini to the 4 pin Male XLR adapter.
#Strip away a portion of the red and black cables inside the pigtail, revealing the copper wire inside.
#*The microphone will be connected via the input terminals of the STM-1 (Red to +, Black to -, ground to the ground terminal).
# Connect the female XLR to the Male XLR adapter
#Connect the other ends of the 22/2 cable to the terminals on F41.
:*The audio line will be connected to a 3.5mm audio cable (cut approx. 12") with B-connectors and inserted in the "Audio In" port
:*Power will be connected to the I/O connector (Black to 1, Red to 2)
: [[File:F41CompleteWiring.jpg|link=https://ipivs.com/wiki/images/5/5e/F41CompleteWiring.jpg]]

@@ Line 15: / Line 15: @@
 #Measure center of the drop ceiling tile and drill a similar hole with the ½” paddle bit.
 #Align the single gang plate to the location of the microphone on the drop ceiling tile using a pair of toggle bolts.
-#:[[File:Plate_Mounted_to_Ceiling.JPG|400x300px|link=https://ipivs.com/wiki/images/5/5d/Plate_Mounted_to_Ceiling.JPG]]
+#: {{img | file = Plate_Mounted_to_Ceiling.JPG | width=250px}}
 #Run the MX202i through the ½” hole in the ceiling tile and single gang plate with the rubber stopper to secure the microphone in place and plugging the ½” hole .
 #Adjust the length of the cable of the microphone to a desirable length, hiding the remainder in the ceiling near the STM-1. Attach the windscreen to the MX202i.
-#:[[File:Mx202i.jpg|link=https://ipivs.com/wiki/images/9/9d/Mx202i.jpg|300px]]
+#: {{img | file = Mx202i.jpg | width=250px}}
 # Run the XLR mini cable to the STM-1 location.
 #Connect the connect the XLR mini to the 4 pin Male XLR adapter.
@@ Line 27: / Line 27: @@
 :*The audio line will be connected to a 3.5mm audio cable (cut approx. 12") with B-connectors and inserted in the "Audio In" port
 :*Power will be connected to the I/O connector (Black to 1, Red to 2)
-: [[File:F41CompleteWiring.jpg|link=https://ipivs.com/wiki/images/5/5e/F41CompleteWiring.jpg]]
+: {{img | file = F41CompleteWiring.jpg | width=400px}}

@@ Line 2: / Line 2: @@
 #Cut a short piece of 22/2 cable (approx. 1 inch). Strip the jacket and from the cable and remove all contents keeping only the red cable. On both ends of the red cable, strip off a piece of the jacket (See picture).
-#:[[File:Phantom Power Jumper.JPG|400x300px|link=https://ipivs.com/wiki/images/8/87/Phantom_Power_Jumper.JPG]]
+#: {{img | file = Phantom Power Jumper.JPG | width=200px}}
 #Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
-#:[[File:Phantom PWR STM.JPG|400x300px|link=https://ipivs.com/wiki/images/b/b3/Phantom_PWR_STM.JPG]]
+#: {{img | file = Phantom PWR STM.JPG | width=500px}}
 #Connect the cable ran for power to both PWR terminals (Red to +, Black to the other terminal) of the STM-1. Connect the other side to the IO phoenix connector (Red to 2, Black to 1).
 #Connect the cable ran for audio to both LO-Z OUTPUT terminals (Red to +, Black to -, and ground to the ground terminal) of the STM-1. Connect the other end of the 3.5mm cable to the in on the F41. (cut to appropriate length between STM-1 and F41)
-#:[[File:STM1F41.jpeg|400x300px|link=https://ipivs.com/wiki/images/d/dc/STM1F41.jpeg]]
+#: {{img | file = STM1F41.jpeg | width=500px}}
 ==Connecting and Mounting the Microphone==