Template:P3364 Installation Instructions - Revision history

IVSWikiBlue at 21:17, 24 March 2025

2025-03-24T21:17:20Z

IVSWikiBlue at 17:09, 24 March 2025

2025-03-24T17:09:48Z

IVSWikiBlue: /* Installation Instructions */

2022-08-02T17:30:05Z

‎Installation Instructions

IVSWikiBlue: /* Disassemble the Camera */

2022-08-02T17:29:50Z

‎Disassemble the Camera

IVSWikiBlue: /* Installation Instructions */

2022-08-02T17:29:14Z

‎Installation Instructions

IVSWikiBlue: /* Connecting the IFPX */

2021-03-17T19:31:55Z

‎Connecting the IFPX

IVSWikiBlue: Created page with "==Installation Instructions== ===Disassemble the Camera=== #Locate the network drop above the ceiling. It should be terminated with a male Ethernet end (service loop) or a bi..."

2020-05-13T15:55:37Z

Created page with "==Installation Instructions== ===Disassemble the Camera=== #Locate the network drop above the ceiling. It should be terminated with a male Ethernet end (service loop) or a bi..."

New page

==Installation Instructions==

===Disassemble the Camera===
#Locate the network drop above the ceiling. It should be terminated with a male Ethernet end (service loop) or a biscuit jack. This line will have been ran back to the POE switch.
#:''Note:'' If the switch does not have POE, a POE injector will need to be installed at the network closet.
#Using the T20 bit, remove the dome from the 3364/65.
===Mounting the IFPX===
#Using a set of wall dog screws, mount the Louroe IFPX above into the drywall above drop ceiling.
#:''Note:'' If no drop ceiling make other arrangements to mount the IFPX.
#Connect the network drop into the RJ-45 (f) on the IFPX that reads '''Power+Data In'''. When connected, activity will be seen on the link lights. If no link lights, ensure that POE is enabled on the POE switch and that the network drop is plugged in.

=== Drywall Mounting instructions===
#Determine mounting height and location
#Using a stud finder, ensure there aren’t any studs any behind the camera base.
#Using a pencil, mark the two holes where the camera base well be attached
#Mark another location to run cabling behind the drywall
#Drill the marked locations
#Using the hole saw, drill a hole above the drop ceiling in line with the hole drilled where the camera will be mounted.
#Insert anchors
#Using glow rods or fish tape, run the 22/2, 3.5mm, and network cable behind drywall
#Mount the camera using screws

=== Drop Ceiling Inscructions===
#Remove the ceiling tile the camera will be mounted to and determine where on the tile to mount.
#Using a pencil, mark the two holes where the camera base well be attached
#Make a small hole that can be hidden by the camera dome for running cabling through.
#Using toggle bolts, mount the camera.
#Return ceiling tile with mounted camera to drop ceiling.
#Run 22/2, 3.5 mm, and network cable to IFPX location

===Connecting the IFPX===
#Using the CAT5/6 patch cable, connect the camera to the RJ-45 (f) on the IFPX, labeled '''Power+Data Out'''. When connected, you should see the '''NET''', '''STATUS''', and '''POWER''' LEDs light up on the camera. After approximately 1 minute, all 3 should be green. If not, check connections.
#Take the 3.5mm Male to Male audio cable and connect it from the 3.5mm jack labeled '''AUDIO OUT''' on the IFPX, into the pink '''AUDIO IN''' on the P3364 or P3365 camera. (See Picture)
#:[[File:IFPX_to_3365.JPG|400x300px]]

← Older revision		Revision as of 21:17, 24 March 2025
Line 45:		Line 45:
	</div>		</div>

−	[[Category:Axis P3364]]	+	<includeonly>[[Category:Axis P3364]]</includeonly>

← Older revision		Revision as of 17:09, 24 March 2025
Line 44:		Line 44:
	#:[[File:IFPX_to_3365.JPG\|400x300px\|link=https://ipivs.com/wiki/images/6/63/IFPX_to_3365.JPG]]		#:[[File:IFPX_to_3365.JPG\|400x300px\|link=https://ipivs.com/wiki/images/6/63/IFPX_to_3365.JPG]]
	</div>		</div>
		+
		+	[[Category:Axis P3364]]

@@ Line 9: / Line 9: @@
 ===Mounting the IFPX===
 #Using a set of wall dog screws, mount the Louroe IFPX above into the drywall above drop ceiling.
 #:''Note:'' If no drop ceiling make other arrangements to mount the IFPX.

@@ Line 5: / Line 5: @@
 #Locate the network drop above the ceiling. It should be terminated with a male Ethernet end (service loop) or a biscuit jack. This line will have been ran back to the POE switch.
 #:''Note:'' If the switch does not have POE, a POE injector will need to be installed at the network closet.
 #Using the T20 bit, remove the dome from the 3364/65.
 ===Mounting the IFPX===
 #Using a set of wall dog screws, mount the Louroe IFPX above into the drywall above drop ceiling.

@@ Line 2: / Line 2: @@
 ===Disassemble the Camera===
 #Locate the network drop above the ceiling. It should be terminated with a male Ethernet end (service loop) or a biscuit jack. This line will have been ran back to the POE switch.
 #:''Note:'' If the switch does not have POE, a POE injector will need to be installed at the network closet.
@@ Line 9: / Line 10: @@
 #:''Note:'' If no drop ceiling make other arrangements to mount the IFPX.
 #Connect the network drop into the RJ-45 (f) on the IFPX that reads '''Power+Data In'''. When connected, activity will be seen on the link lights. If no link lights, ensure that POE is enabled on the POE switch and that the network drop is plugged in.
 === Drywall Mounting instructions===
 #Determine mounting height and location
 #Using a stud finder, ensure there aren’t any studs any behind the camera base.
@@ Line 20: / Line 23: @@
 #Using glow rods or fish tape, run the 22/2, 3.5mm, and network cable behind drywall
 #Mount the camera using screws
 === Drop Ceiling Inscructions===
 #Remove the ceiling tile the camera will be mounted to and determine where on the tile to mount.
 #Using a pencil, mark the two holes where the camera base well be attached
@@ Line 28: / Line 33: @@
 #Return ceiling tile with mounted camera to drop ceiling.
 #Run 22/2, 3.5 mm, and network cable to IFPX location
 ===Connecting the IFPX===
 #Using the CAT5/6 patch cable, connect the camera to the RJ-45 (f) on the IFPX, labeled '''Power+Data Out'''. When connected, you should see the '''NET''', '''STATUS''', and '''POWER''' LEDs light up on the camera. After approximately 1 minute, all 3 should be green. If not, check connections.
 #Take the 3.5mm Male to Male audio cable and connect it from the 3.5mm jack labeled '''AUDIO OUT''' on the IFPX, into the pink '''AUDIO IN''' on the P3364 or P3365 camera. (See Picture)
 #:[[File:IFPX_to_3365.JPG|400x300px|link=https://ipivs.com/wiki/images/6/63/IFPX_to_3365.JPG]]