Template:P3364 STMwiring - Revision history

IVSWikiBlue: /* Connecting Wiring */

2022-08-02T17:44:40Z

‎Connecting Wiring

IVSWikiBlue: /* Connecting Wiring */

2021-03-17T19:36:38Z

‎Connecting Wiring

IVSWikiBlue: Created page with "== Connecting Wiring== #Strip the jacket off the 22/2, revealing the red, black, and common (bare wires) on both cables. Remove the string and plastic casings covering the re..."

2020-05-13T16:02:45Z

Created page with "== Connecting Wiring== #Strip the jacket off the 22/2, revealing the red, black, and common (bare wires) on both cables. Remove the string and plastic casings covering the re..."

New page

== Connecting Wiring==
#Strip the jacket off the 22/2, revealing the red, black, and common (bare wires) on both cables. Remove the string and plastic casings covering the red and black cables. Strip the red and black jackets off the wire exposing the copper. Cut copper evenly. On the cable we ran for power, remove the common (bare wire) completely.
#Cut a 3.5 mm audio cable in half. Strip about an inch of the black jacket; then strip about 1/2 inch of red and white strand jacket. Test the 3.5 cable for polarity (touch one end of the cable tester to the tip of the 3.5 jack and the other end to the red and white wires. This will be the positive wire; the middle section of the 3.5 jack is negative wire; the bottom section of the jack is ground/stranded wire.) Splice these wires with the camera end of the 22/2 cable we just ran for audio.
#Connect the power cable to the IO phoenix connector (Red to 2, Black to 1).
#Plug in the network drop to the PoE NIC, the 3.5 jack into the pink AUDIO IN port on the camera, and the IO phoenix connector to the IO port.
#You will also need to cut another shorter piece of 22/2 cable (approx. 1 inch). Strip the jacket from the cable and remove all contents keeping only the red cable. On both ends of the red cable, strip off a piece of the jacket (See picture).
#:[[File:Phantom Power Jumper.JPG|400x300px]]

@@ Line 1: / Line 1: @@
 == Connecting Wiring==
 #Strip the jacket off the 22/2, revealing the red, black, and common (bare wires) on both cables. Remove the string and plastic casings covering the red and black cables. Strip the red and black jackets off the wire exposing the copper. Cut copper evenly. On the cable we ran for power, remove the common (bare wire) completely.
 #Cut a 3.5 mm audio cable in half. Strip about an inch of the black jacket; then strip about 1/2 inch of red and white strand jacket. Test the 3.5 cable for polarity (touch one end of the cable tester to the tip of the 3.5 jack and the other end to the red and white wires. This will be the positive wire; the middle section of the 3.5 jack is negative wire; the bottom section of the jack is ground/stranded wire.) Splice these wires with the camera end of the 22/2 cable we just ran for audio.
@@ Line 6: / Line 7: @@
 #You will also need to cut another shorter piece of 22/2 cable (approx. 1 inch). Strip the jacket from the cable and remove all contents keeping only the red cable. On both ends of the red cable, strip off a piece of the jacket (See picture).
 #:[[File:Phantom Power Jumper.JPG|400x300px|link=https://ipivs.com/wiki/images/8/87/Phantom_Power_Jumper.JPG]]

@@ Line 5: / Line 5: @@
 #Plug in the network drop to the PoE NIC, the 3.5 jack into the pink AUDIO IN port on the camera, and the IO phoenix connector to the IO port.
 #You will also need to cut another shorter piece of 22/2 cable (approx. 1 inch). Strip the jacket from the cable and remove all contents keeping only the red cable. On both ends of the red cable, strip off a piece of the jacket (See picture).
-#:[[File:Phantom Power Jumper.JPG|400x300px]]
+#:[[File:Phantom Power Jumper.JPG|400x300px|link=https://ipivs.com/wiki/images/8/87/Phantom_Power_Jumper.JPG]]