Tubular LED Key Switch - Revision history

IVSWikiBlue at 18:55, 24 March 2025

2025-03-24T18:55:43Z

IVSWikiBlue at 19:02, 11 May 2022

2022-05-11T19:02:14Z

IVSWikiBlue: /* Installation Instructions */

2020-04-20T16:22:04Z

‎Installation Instructions

IVSWikiBlue: /* Installation Instructions */

2017-02-16T14:10:06Z

‎Installation Instructions

IVSWikiBlue at 19:28, 20 January 2017

2017-01-20T19:28:02Z

IVSWikiBlue at 19:39, 5 January 2017

2017-01-05T19:39:49Z

IVSWikiBlue at 19:38, 5 January 2017

2017-01-05T19:38:44Z

IVSWikiBlue at 19:27, 5 January 2017

2017-01-05T19:27:27Z

IVSWikiBlue at 19:26, 5 January 2017

2017-01-05T19:26:33Z

IVSWikiBlue at 19:25, 5 January 2017

2017-01-05T19:25:29Z

← Older revision		Revision as of 18:55, 24 March 2025
Line 33:		Line 33:
	#On the other end, connect the 22/4 exposed copper securely into the I/O Phoenix connector. Ensure that the wiring on is consistent from the keys switch (See Picture Below).		#On the other end, connect the 22/4 exposed copper securely into the I/O Phoenix connector. Ensure that the wiring on is consistent from the keys switch (See Picture Below).
	#:{{img \| file = Wired_IO_Connector.JPG \| width=300px}}		#:{{img \| file = Wired_IO_Connector.JPG \| width=300px}}
		+
		+	[[Category:Accessories]]

@@ Line 1: / Line 1: @@
 ==Required Parts And Tools==
-* Securitron KP-1 [[File:Securitron KP1.JPG|60x80px]]
+* Securitron KP-1
-* Wire Stripper [[File:Wire_Stripper_and_Starbit_Driver.JPG|60x80px]]
+:{{img | file = Securitron KP1.JPG | width=80px}}
-* Small Flat head screwdriver [[File:Small_Flathead_Screwdriver.JPG|60x80px]]
+* Wire Stripper
-* B Connectors [[File:BCONN.png|60x80px]]
+:{{img | file = Wire_Stripper_and_Starbit_Driver.JPG | width=80px}}
 * Stud Finder
-* 22/4 Solid Gauge Wire [[File:Audio_Cable.JPG|60x80px]]
+* 22/4 Solid Gauge Wire
-* Fish Tape or Glow Rod [[File:15-4-57-m-mid-flex-glow-rod-set-tools-to-k56415-to-k56415-19671-228x228.jpg|60x80px]]
+:{{img | file = Audio_Cable.JPG | width=80px}}
-* DryWall Saw [[File:DryWall_Saw.JPG|60x80px]]
+* Fish Tape or Glow Rod
-* Mud Ring [[File:Mud_Ring.JPG|60x80px]]
+:{{img | file = 15-4-57-m-mid-flex-glow-rod-set-tools-to-k56415-to-k56415-19671-228x228.jpg | width=80px}}
 * Electrical Tape
@@ Line 19: / Line 27: @@
 #Strip the jacket off of both ends of the cable revealing the 4 individual strands of cable. Strip those individual cables revealing their solid copper inside.
 #Open the Secuitron KeySwitch and strip the red and white leads from the tubular key portion revealing the stranded silver cable, and strip the back and red leads coming from the LED revealing the stranded silver cable.
-[[File:KeySwitch Wires.JPG|400x300px]] [[File:LED WIRES Labeled.JPG|400x300px]]
+#:{{img | file = KeySwitch Wires.JPG | width=300px}} {{img | file = LED WIRES Labeled.JPG | width=300px}}
 #Wind the silver stranded cable around the solid copper of the 22/4 following the picture below. When wired, secure these connections with B-Connectors.
-#:[[File:Switch All Wired.JPG|400x300px]]
+#:{{img | file = Switch All Wired.JPG | width=300px}}
 #Once B-Connectors are secure, use the electrical tape to secure these wires together and place the excess into the wall. Screw the Securitron Key Switch into the mud ring mounting it flush to the wall.
 #On the other end, connect the 22/4 exposed copper securely into the I/O Phoenix connector. Ensure that the wiring on is consistent from the keys switch (See Picture Below).
-#:[[File:Wired_IO_Connector.JPG|400x300px]]
+#:{{img | file = Wired_IO_Connector.JPG | width=300px}}

@@ Line 14: / Line 14: @@
 ==Installation Instructions==
-#Determine where you want your Securitron Tubular Key Switch to be placed. Use your stud finder to determine that there aren't any studs behind the wall.
+#Determine where the Securitron Tubular Key Switch to be located. Using a stud finder, determine that there aren't any studs behind the wall.
-#Using your drywall saw, cut a rectangle in the drywall large enough to fit the mud ring into securely.
+#Using a drywall saw, cut a rectangle in the drywall large enough to fit the mud ring into securely.
-#Using your glow rod or fish tape, fish your 22/4 cable up and through the wall and ceiling until you reach the location of your camera.
+#Using glow rods or fish tape, fish the 22/4 cable up and through the wall and ceiling the location of the camera is reached.
 #Strip the jacket off of both ends of the cable revealing the 4 individual strands of cable. Strip those individual cables revealing their solid copper inside.
 #Open the Secuitron KeySwitch and strip the red and white leads from the tubular key portion revealing the stranded silver cable, and strip the back and red leads coming from the LED revealing the stranded silver cable.
 [[File:KeySwitch Wires.JPG|400x300px]] [[File:LED WIRES Labeled.JPG|400x300px]]
 #Wind the silver stranded cable around the solid copper of the 22/4 following the picture below. When wired, secure these connections with B-Connectors.

@@ Line 18: / Line 18: @@
 #Using your glow rod or fish tape, fish your 22/4 cable up and through the wall and ceiling until you reach the location of your camera.
 #Strip the jacket off of both ends of the cable revealing the 4 individual strands of cable. Strip those individual cables revealing their solid copper inside.
-#Open the Secuitron KeySwitch and strip the red and white leads from the tubular key portion revealing the stranded silver cable, and strip the back and red leads coming from the LED revealing the stranded silver cable.[[File:KeySwitch Wires.JPG|400x300px]] [[File:LED WIRES Labeled.JPG|400x300px]]
+#Open the Secuitron KeySwitch and strip the red and white leads from the tubular key portion revealing the stranded silver cable, and strip the back and red leads coming from the LED revealing the stranded silver cable.
 #Wind the silver stranded cable around the solid copper of the 22/4 following the picture below. When wired, secure these connections with B-Connectors.
 #:[[File:Switch All Wired.JPG|400x300px]]

@@ Line 10: / Line 10: @@
 * DryWall Saw [[File:DryWall_Saw.JPG|60x80px]]
 * Mud Ring [[File:Mud_Ring.JPG|60x80px]]
 ==Installation Instructions==
@@ Line 20: / Line 21: @@
 #Wind the silver stranded cable around the solid copper of the 22/4 following the picture below. When wired, secure these connections with B-Connectors.
 #:[[File:Switch All Wired.JPG|400x300px]]
-#Once B-Connectors are secure, screw the Securitron Key Switch into the mud ring.
+#Once B-Connectors are secure, use the electrical tape to secure these wires together and place the excess into the wall. Screw the Securitron Key Switch into the mud ring mounting it flush to the wall.
 #On the other end, connect the 22/4 exposed copper securely into the I/O Phoenix connector. Ensure that the wiring on is consistent from the keys switch (See Picture Below).
 #:[[File:Wired_IO_Connector.JPG|400x300px]]

← Older revision		Revision as of 19:38, 5 January 2017
Line 20:		Line 20:
	#Wind the silver stranded cable around the solid copper of the 22/4 following the picture below. When wired, secure these connections with B-Connectors.		#Wind the silver stranded cable around the solid copper of the 22/4 following the picture below. When wired, secure these connections with B-Connectors.
	#:[[File:Switch All Wired.JPG\|400x300px]]		#:[[File:Switch All Wired.JPG\|400x300px]]
		+	#Once B-Connectors are secure, screw the Securitron Key Switch into the mud ring.
		+	#On the other end, connect the 22/4 exposed copper securely into the I/O Phoenix connector. Ensure that the wiring on is consistent from the keys switch (See Pictures Below).
		+	#:[[File:Wired_IO_Connector.JPG\|400x300px]]