Video Decoder - Revision history

IVSWikiBlue: /* Camera Configuration */

2023-01-30T18:36:27Z

‎Camera Configuration

2023-01-30T18:35:46Z

‎Camera Configuration

2023-01-30T18:32:43Z

‎Installation Instructions

2023-01-30T18:32:13Z

‎Camera Configuration

2023-01-30T18:26:01Z

2021-03-17T19:30:50Z

2020-05-01T15:27:59Z

‎Required Parts And Tools

2020-04-21T16:15:57Z

‎Decoder Configuration

2020-04-21T16:14:48Z

‎Installation Instructions

2020-04-01T19:26:48Z

‎Decoder Configuration

@@ Line 28: / Line 28: @@
 The Cameras' authentication must be set to <b>Encrypted</b> or <b>Digest</b>
-<b>Note:</b> <i>Some updated Axis UI may show a saved change to Digest, but it may not actually be saved. Double-check your settings to ensure proper implementation.</i>
+<b>Note:</b> <i>Some updated Axis UI may show a saved change to Digest, but it may not actually be saved. Moving to the older UI will sometimes show the setting is still on Basic.</i>
 </div>

@@ Line 27: / Line 27: @@
 <div class="floating_card">
 The Cameras' authentication must be set to <b>Encrypted</b> or <b>Digest</b>
 </div>

@@ Line 11: / Line 11: @@
 ==Installation Instructions==
 <div class="section">
 #Using a stud finder, ensure there aren’t any studs where the decoder will be mounted. Make a mark where the mount will be screwed to the wall.
 #Using the drill bit, drill the screw marker and place the anchor inside.

@@ Line 23: / Line 23: @@
 ==Camera Configuration==
 <div class="section">
-'''The Cameras' authentication must be set to Encrypted or Digest'''
+) Navigate to the IP of the camera.
-#) Navigate to the IP of the camera.
+) For '''Allow Password Type''', select '''Encrypted''', if it is not already.
-#) (In the old navigation view) Go to '''Setup''' in the top right; then '''System Options'''.
+</div>
-#) For '''Allow Password Type''', select '''Encrypted''', if it is not already.
+[[File:Start_stop_unencrypt.png|link=https://ipivs.com/wiki/images/7/77/Start_stop_unencrypt.png]]
-#) (In the new navigation view) Go to '''Settings'''; then '''System'''; then '''Plain Config'''.
+<div class="section">
-#:[[File:Start_stop_unencrypt_new.png|link=https://ipivs.com/wiki/images/8/83/Start_stop_unencrypt_new.png]]
+) (In the new navigation view) Go to '''Settings'''; then '''System'''; then '''Plain Config'''.
 </div>
 ==Decoder Configuration==

@@ Line 1: / Line 1: @@
 ==Required Parts And Tools==
 * Axis T8705 Unit
@@ Line 7: / Line 8: @@
 * Cat5/6 Patch Cable (1ft-3ft recommended)
 * HDMI cable for customer's monitor (HDMI to DVI or Display Port, if necessary)
 ==Installation Instructions==
+<div class="section">
 '''First, determine whether our customer prefers it to be mounted to the wall behind the monitor, or to the back of the monitor itself'''
@@ Line 18: / Line 20: @@
 #Plug the network cable into the Decoder, then into the network jack.
 #Plug in the power cable for the Decoder.
 ==Camera Configuration==
+<div class="section">
 '''The Cameras' authentication must be set to Encrypted or Digest'''
@@ Line 33: / Line 36: @@
 #) Under '''HTTP''', '''Authentication Policy''' should be set to '''Digest'''. Scroll to click '''Save'''.
 #:[[File:Start_stop_unencrypt_new_2.png|link=https://ipivs.com/wiki/images/3/32/Start_stop_unencrypt_new_2.png]]
+</div>
 ==Decoder Configuration==
-The Decoder will need to be accessed, either over the network or directly via a laptop.
+<div class="section">
 #) On the Video Sources tab, click '''Add Camera'''.
 #) Add the name, IP, username, and password of the cameras one at a time.
 #) On the Display tab, select '''Multiview''' for Multimode, and the appropriate view matrix for View.

@@ Line 3: / Line 3: @@
 * Anchors and Screws
 * Drill bit and drill
 * Phillips head drill bit or Phillips head screwdriver
 * Cat5/6 Patch Cable (1ft-3ft recommended)
-*:[[File:Cat6_Patch_Cable.JPG|60x80px]]
+* HDMI cable for customer's monitor (HDMI to DVI or Display Port, if necessary)
 ==Installation Instructions==

@@ Line 44: / Line 44: @@
 You will need to access the Decoder, either over the network or directly from your laptop.
-#) On the Video Sources tab, click "Add Camera".
+#) On the Video Sources tab, click '''Add Camera'''.
 #) Add the name, IP, username, and password of the cameras one at a time.
-#) On the Display tab, select Multiview for Multimode, and the appropriate view matrix for View.
+#) On the Display tab, select '''Multiview''' for Multimode, and the appropriate view matrix for View.