Difference between revisions of "Template:VALT Keypad 2 - Old"

From IVS Wiki
Jump to: navigation, search
m (IVSWikiBlue moved page Valt PIN Code Keypad to Template:VALT Keypad 2 - Old without leaving a redirect)
 
(18 intermediate revisions by the same user not shown)
Line 2: Line 2:
 
===How to Connect===
 
===How to Connect===
 
Attach the wiring according to the following diagrams:  
 
Attach the wiring according to the following diagrams:  
−
: [[Keypad_Guts.jpg|400x300px]]
+
: [[File:Keypad_Guts.jpg|400x300px]]
−
: [[Keypad_Pad.jpg|400x300px]]
+
: [[File:Keypad_Pad.jpg|400x300px]]
−
: [[Keypad_Screen.jpg|400x300px]]
+
: [[File:Keypad_Screen.jpg|400x300px]]
  
 
====DHCP====
 
====DHCP====
−
The Valt Keypad will automatically pull an IP address from DHCP. The IP address can be obtained by reviewing your DHCP leases on your DHCP server. The hostname of the device is Keypad.
+
The Valt Keypad will automatically pull an IP address from DHCP. The IP address can be obtained by reviewing DHCP leases on the associated DHCP server. The hostname of the device is Keypad.
 +
 
 
====Static====
 
====Static====
−
If no DHCP server is available the Valt Keypad will default to a static IP address of 192.168.0.92.
+
If no DHCP server is available, the Valt Keypad will default to a static IP address of 192.168.0.92.
 
====Manual====
 
====Manual====
−
You can retrieve the IP address from the keypad directly by plugging in a keyboard and running the following command from the console:
+
The IP address from the keypad may also be obtained directly by plugging in a keyboard and running the following command from the console:
−
'''ifconfig | more'''
+
<pre>ifconfig | more</pre>
  
−
The ip address will be listed under interface eth0.
+
The IP address will be listed under interface '''eth0'''.
  
 
===Manually Setting an IP Address===
 
===Manually Setting an IP Address===
−
In order to set the ip address manually you must be connected to the Keypad using the ivsadmin user. The ivsuser account can not change any settings. If you are connecting from the console, type '''su ivsadmin''' to change accounts. You will be prompted for the ivsadmin password.
+
In order to set the IP address manually, connect to the Keypad using the ivsadmin user. The ivsuser account cannot change any settings. If connecting from the console, type the following to change accounts. There will be prompt for the ivsadmin password. <pre>su ivsadmin</pre>
−
# Type ''' sudo nano /etc/dhcpcd.conf''' and press enter
+
# Type the following, and press Enter: <pre>sudo nano /etc/dhcpcd.conf</pre>
−
# Scroll down until you find the section for interface eth0.
+
# Scroll down until to the section for interface '''eth0'''.
−
# Remove the # at the start of the lines for static ip_address, static routers, and static domain_name_servers.
+
# Remove the '''#''' at the start of the lines for static IP, static routers, and static domain_name_servers.
−
# Update the ip configuration to reflect the correct settings for your environment.
+
# Update the IP configuration to reflect the correct settings for the environment.
 
#:[[File:SmartButton2.png]]
 
#:[[File:SmartButton2.png]]
−
# Comment out the remaining lines in the file by adding a # to the start of the line.
+
# Comment out the remaining lines in the file by adding a '''#''' to the start of the line.
 
#:[[File:SmartButton3.png]]
 
#:[[File:SmartButton3.png]]
−
 
  
 
===Configuring the Keypad===
 
===Configuring the Keypad===
−
#Type '''sudo nano /home/ivsuser/.bashrc''' and press enter.
+
# Type the following, and press Enter: <pre>sudo nano /home/ivsuser/.bashrc</pre>
−
#Scroll down to the bottom of the file
+
# Scroll down to the bottom of the file.
−
#:[[File:SmartButton1.png]]
+
#:[[File:Keypad_script.png|800px]]
−
# Modify the last command in the file to match your environment. Make sure to remove the # from the beginning of the line. The settings are listed below.  
+
# Modify the last command in the file to match your environment. Make sure to remove the '''#''' from the beginning of the line. The settings are listed below.  
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
Line 50: Line 50:
 
|}
 
|}
  
−
Reboot the keypad (sudo reboot) and it should begin functioning normally.
+
Reboot the keypad using the following command: <pre>sudo reboot</pre>
 +
 
 +
The keypad should begin functioning normally.
 +
 
 +
===Star Commands===
 +
Typing any of the commands in the table below into the keypad will result in triggering a special function.
 +
{| class="wikitable"
 +
|-
 +
|*1
 +
|Share Current Recording With A User
 +
|-
 +
|*2
 +
|Share Current Recording With A Group
 +
|-
 +
|*3
 +
|Pause Current Recording
 +
|-
 +
|*4
 +
|Add a Marker
 +
|-
 +
|*5
 +
|Not Used Currently
 +
|-
 +
|*6
 +
|Not Used Currently
 +
|-
 +
|*7
 +
|Menu
 +
|-
 +
|*8
 +
|Reboot Keypad
 +
|-
 +
|*9
 +
|Display IP Address
 +
|-
 +
|*0
 +
|Reset LED Display
 +
|}
  
 
===Disable the Fan===
 
===Disable the Fan===
−
# Connect to the keypad via SSH
+
# Connect to the keypad via SSH.
−
# Type '''sudo nano /boot/config.txt''' and press enter.
+
# Type the following, and press Enter: <pre>sudo nano /boot/config.txt</pre>
−
# Scroll down to the bottom of the file and add the following line:
+
# Scroll down to the bottom of the file and add the following line: <pre>disable_poe_fan=1</pre>
−
#: disable_poe_fan=1
+
# Save the file.
−
# Save the file
 
 
# Reboot the keypad.
 
# Reboot the keypad.

Latest revision as of 15:40, 29 March 2024

Configuration

How to Connect

Attach the wiring according to the following diagrams:

Keypad Guts.jpg
Keypad Pad.jpg
Keypad Screen.jpg

DHCP

The Valt Keypad will automatically pull an IP address from DHCP. The IP address can be obtained by reviewing DHCP leases on the associated DHCP server. The hostname of the device is Keypad.

Static

If no DHCP server is available, the Valt Keypad will default to a static IP address of 192.168.0.92.

Manual

The IP address from the keypad may also be obtained directly by plugging in a keyboard and running the following command from the console: 

ifconfig | more

The IP address will be listed under interface eth0.

Manually Setting an IP Address

In order to set the IP address manually, connect to the Keypad using the ivsadmin user. The ivsuser account cannot change any settings. If connecting from the console, type the following to change accounts. There will be prompt for the ivsadmin password. 
su ivsadmin
  1. Type the following, and press Enter: 
    sudo nano /etc/dhcpcd.conf
  2. Scroll down until to the section for interface eth0.
  3. Remove the # at the start of the lines for static IP, static routers, and static domain_name_servers.
  4. Update the IP configuration to reflect the correct settings for the environment.
    SmartButton2.png
  5. Comment out the remaining lines in the file by adding a # to the start of the line.
    SmartButton3.png

Configuring the Keypad

  1. Type the following, and press Enter: 
    sudo nano /home/ivsuser/.bashrc
  2. Scroll down to the bottom of the file.
    Keypad script.png
  3. Modify the last command in the file to match your environment. Make sure to remove the # from the beginning of the line. The settings are listed below.
-s Server IP Address or DNS entry
-u Valt Username
-p Valt Password
-r Valt Room Number
--ssl True if the Valt server is using https, otherwise omit this option.
Reboot the keypad using the following command: 
sudo reboot

The keypad should begin functioning normally.

Star Commands

Typing any of the commands in the table below into the keypad will result in triggering a special function.

*1 Share Current Recording With A User
*2 Share Current Recording With A Group
*3 Pause Current Recording
*4 Add a Marker
*5 Not Used Currently
*6 Not Used Currently
*7 Menu
*8 Reboot Keypad
*9 Display IP Address
*0 Reset LED Display

Disable the Fan

  1. Connect to the keypad via SSH.
  2. Type the following, and press Enter: 
    sudo nano /boot/config.txt
  3. Scroll down to the bottom of the file and add the following line: 
    disable_poe_fan=1
  4. Save the file.
  5. Reboot the keypad.
Retrieved from "https://ipivs.info/wiki/index.php?title=Template:VALT_Keypad_2_-_Old&oldid=12670"