Difference between revisions of "5525 Wall Mount Instructions"

From IVS Wiki
Jump to: navigation, search
 
(7 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
#Locate the AXIS T91E61 Wall Mount.
+
{{Article | title = {{PAGENAME}} | content =
−
#:''This is the recommended wall mount by IVS. Verify the model of your mount [[AXIS 5525 Wall Mount Types|here]]''.
+
{{Flexbox
−
#:[[File:T91E61 Wall Mount.png|275px|link=https://ipivs.com/wiki/images/b/ba/T91E61_Wall_Mount.png]]
+
| left =
−
#Locate the AXIS T94A01D Pendant Kit.
+
1. Locate the AXIS T91E61 Wall Mount.
−
#:[[File:T94A01D Pendant Kit.png|200px|link=https://ipivs.com/wiki/images/d/dc/T94A01D_Pendant_Kit.png]]
+
:''This is the recommended wall mount by IVS. Verify the model of your mount [[AXIS 5525 Wall Mount Types|here]]''.
−
#Connect the two parts and tighten them together by hand.
+
| right = [[File:T91E61 Wall Mount.png|275px|link=]]
−
#:[[File:Connect.png|250px|link=https://ipivs.com/wiki/images/5/5f/Connect.png]]
+
}}
−
#Continue tightening, by hand, until you cannot rotate the pendant kit anymore.
+
 
−
#:[[File:Connected.png|200px|link=https://ipivs.com/wiki/images/c/cd/Connected.png]]
+
{{hr}}
−
#Using a T20 bit, tighten down the screw located inside the pendant kit.
+
 
−
#:[[File:ScrewLock.png|250px|link=https://ipivs.com/wiki/images/d/de/ScrewLock.png]]
+
{{Flexbox
−
#Locate the mounting plate.
+
| left =
−
#:''This part comes packed with the AXIS M5525.''
+
2. Locate the AXIS T94A01D Pendant Kit.
−
#:[[File:5525 Disk.png|250px|link=https://ipivs.com/wiki/images/f/f8/5525_Disk.png]]
+
| right =
−
#Take the camera disk and line up the 3 pegs on the top with the three holes on the pendant kit.
+
[[File:T94A01D Pendant Kit.png|200px|link=]]
−
#:[[File:Camera disk2.png|500px|link=https://ipivs.com/wiki/images/6/6e/Camera_disk2.png]]
+
}}
−
#Put the pegs in the holes and rotate the disk counter clockwise until the pieces prevent you from turning more.  
+
 
−
#:[[File:Camera disk.png|400px|link=https://ipivs.com/wiki/images/5/56/Camera_disk.png]]
+
{{hr}}
−
#Using a T30 bit, tighten the three screws on top of the pendant kit, securing it to the camera disk.
+
 
−
#:[[File:Large screws3.png|300px|link=https://ipivs.com/wiki/images/0/00/Large_screws3.png]]
+
{{Flexbox
−
#Take the M5525 and plug the ethernet cable into its respective jack on the camera. ''The jack will be listed "PoE".''
+
| left =
−
#:''Please not that only cameras prepared by IVS will have the pigtail wire connected to the camera. To learn more [https://ipivs.com/wiki/M5525_Pigtail click here]''
+
3. Connect the two parts and tighten them together by hand.
−
#:[[File:5525CAT6.png|350px|link=https://ipivs.com/wiki/images/5/52/5525CAT6.png]]
+
| right =
−
#Remove the rubber grommets from the base of the camera and run the cables through the holes.
+
[[File:Connect.png|250px|link=]]
−
#:[[File:Pigtails5525.png|250px|link=https://ipivs.com/wiki/images/1/14/Pigtails5525.png]]
+
}}
−
#Once the camera in the base, locate the four screws attached the camera and tighten them using a T20 bit.
+
 
−
#:[[File:Camera to Base.png|250px|link=https://ipivs.com/wiki/images/f/fe/Camera_to_Base.png]]
+
{{hr}}
−
#Take the assembled wall mount and run the wires ''(that are attached to the camera)'' through the wall mount.
+
 
−
#Match the base of the camera to the bottom of the disc so that the holes for the screws align, allowing the camera to sit comfortably on the mount.  
+
{{Flexbox
−
#:[[File:5525 to mount.png|550px|link=https://ipivs.com/wiki/images/e/e7/5525_to_mount.png]]
+
| left =
−
#:''Use the screws that are provided in a separate bag that comes with the camera.  
+
4. Continue tightening, by hand, until you cannot rotate the pendant kit anymore.
−
#:[[File:Screws.png|200px|link=https://ipivs.com/wiki/images/c/ce/Screws.png]]
+
| right =
−
#:[[File:Cables through mount.png|250px|link=https://ipivs.com/wiki/images/8/8a/Cables_through_mount.png]]
+
[[File:Connected.png|200px|link=]]
−
#
+
}}
−
#:[[File:|350px|link=]]
+
 
−
#
+
{{hr}}
−
#:[[File:|350px|link=]]
+
 
−
#
+
{{Flexbox
−
#:[[File:|350px|link=]]
+
| left =
−
#
+
5. Using a T20 bit, tighten down the screw located inside the pendant kit.
−
#:[[File:|350px|link=]]
+
| right =
 +
[[File:ScrewLock.png|250px|link=]]
 +
}}
 +
 
 +
{{hr}}
 +
 
 +
{{Flexbox
 +
| left =
 +
6. Locate the mounting plate.
 +
:''This part comes packed with the AXIS M5525.''
 +
| right =
 +
[[File:5525 Disk.png|250px|link=]]
 +
}}
 +
 
 +
{{hr}}
 +
 
 +
{{Flexbox
 +
| left =
 +
7. Take the camera disk and line up the 3 pegs on the top with the three holes on the pendant kit.
 +
| right =
 +
[[File:Camera disk2.png|500px|link=]]
 +
}}
 +
 
 +
{{hr}}
 +
 
 +
{{Flexbox
 +
| left =
 +
8. Put the pegs in the holes and rotate the disk counter clockwise until the pieces prevent you from turning more.
 +
| right =
 +
[[File:Camera disk.png|400px|link=]]
 +
}}
 +
 
 +
{{hr}}
 +
 
 +
{{Flexbox
 +
| left =
 +
9. Using a T30 bit, tighten the three screws on top of the pendant kit, securing it to the camera disk.
 +
| right =
 +
[[File:Large screws3.png|300px|link=]]
 +
}}
 +
 
 +
{{hr}}
 +
 
 +
{{Flexbox
 +
| left =
 +
10. Take the M5525 and plug the ethernet cable into its respective jack on the camera. ''The jack will be listed "PoE".''
 +
:''Please note that only cameras prepared by IVS will have the pigtail wire connected to the camera. To learn more [https://ipivs.com/wiki/M5525_Pigtail click here]''
 +
| right =
 +
[[File:5525CAT6.png|350px|link=]]
 +
}}
 +
 
 +
{{hr}}
 +
 
 +
{{Flexbox
 +
| left =
 +
11. Remove the rubber grommets from the base of the camera.
 +
| right =
 +
[[File:5525base.png|350px|link=]]
 +
}}
 +
 
 +
{{hr}}
 +
 
 +
{{Flexbox
 +
| left =
 +
12. Run the cables through the holes where the grommets were.
 +
:''Note that each wire should be in its own hole.''
 +
| right =
 +
[[File:Pigtails5525.png|250px|link=]]
 +
}}
 +
 
 +
{{hr}}
 +
 
 +
{{Flexbox
 +
| left =
 +
13. Once the camera in the base, locate the four screws attached the camera and tighten them using a T20 bit.
 +
| right =
 +
[[File:Camera to Base.png|250px|link=]]
 +
}}
 +
 
 +
{{hr}}
 +
 
 +
{{Flexbox
 +
| left =
 +
14. Take the assembled wall mount and run the wires ''(that are attached to the camera)'' through the wall mount.
 +
Match the base of the camera to the bottom of the disc so that the holes for the screws align, allowing the camera to sit comfortably on the mount.  
 +
| right =
 +
[[File:5525 to mount.png|550px|link=]]
 +
}}
 +
 
 +
{{hr}}
 +
 
 +
{{Flexbox
 +
| left =
 +
15. The camera will naturally sit on the base when everything is aligned properly.
 +
| right =  
 +
[[File:Cables through mount.png|250px|link=]]
 +
}}
 +
 
 +
{{hr}}
 +
 
 +
{{Flexbox
 +
| left =
 +
16. Take the screws provided with the camera, located in the small box, and secure the camera to the mount using all 4 screws.
 +
| right =  
 +
[[File:Camera 2 mount.png|350px|link=]]
 +
}}
 +
 
 +
{{hr}}
 +
 
 +
{{Flexbox
 +
| left =
 +
17. Place the dome back on the camera, making sure to align the plastic of the dome to match the plastic on the mount.
 +
| right =  
 +
[[File:Dome.png|350px|link=]]
 +
}}
 +
 
 +
{{hr}}
 +
 
 +
18. Use a T20 to secure the dome to the camera.
 +
}}

Latest revision as of 08:55, 3 April 2024

5525 Wall Mount Instructions

1. Locate the AXIS T91E61 Wall Mount.

This is the recommended wall mount by IVS. Verify the model of your mount here.

T91E61 Wall Mount.png

2. Locate the AXIS T94A01D Pendant Kit.

T94A01D Pendant Kit.png

3. Connect the two parts and tighten them together by hand.

Connect.png

4. Continue tightening, by hand, until you cannot rotate the pendant kit anymore.

Connected.png

5. Using a T20 bit, tighten down the screw located inside the pendant kit.

ScrewLock.png

6. Locate the mounting plate.

This part comes packed with the AXIS M5525.

5525 Disk.png

7. Take the camera disk and line up the 3 pegs on the top with the three holes on the pendant kit.

Camera disk2.png

8. Put the pegs in the holes and rotate the disk counter clockwise until the pieces prevent you from turning more.

Camera disk.png

9. Using a T30 bit, tighten the three screws on top of the pendant kit, securing it to the camera disk.

Large screws3.png

10. Take the M5525 and plug the ethernet cable into its respective jack on the camera. The jack will be listed "PoE".

Please note that only cameras prepared by IVS will have the pigtail wire connected to the camera. To learn more click here

5525CAT6.png

11. Remove the rubber grommets from the base of the camera.

5525base.png

12. Run the cables through the holes where the grommets were.

Note that each wire should be in its own hole.

Pigtails5525.png

13. Once the camera in the base, locate the four screws attached the camera and tighten them using a T20 bit.

Camera to Base.png

14. Take the assembled wall mount and run the wires (that are attached to the camera) through the wall mount. Match the base of the camera to the bottom of the disc so that the holes for the screws align, allowing the camera to sit comfortably on the mount.

5525 to mount.png

15. The camera will naturally sit on the base when everything is aligned properly.

Cables through mount.png

16. Take the screws provided with the camera, located in the small box, and secure the camera to the mount using all 4 screws.

Camera 2 mount.png

17. Place the dome back on the camera, making sure to align the plastic of the dome to match the plastic on the mount.

Dome.png

18. Use a T20 to secure the dome to the camera.
Retrieved from "https://ipivs.info/wiki/index.php?title=5525_Wall_Mount_Instructions&oldid=12760"