Difference between revisions of "M5525 Shure MX202i"

From IVS Wiki
Jump to: navigation, search
 
(29 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
{{Wirediagram M5525 MX202}}
 +
 
==Required Parts And Tools==
 
==Required Parts And Tools==
  
 
* Axis M5525
 
* Axis M5525
*
 
 
* AXIS T94P01L Recessed Mount
 
* AXIS T94P01L Recessed Mount
*
 
 
* RDL STM-1  
 
* RDL STM-1  
*:[[File:STM-1.JPG|60x80px]]
+
* Female XLR Pigtail
* XLR-F Pigtail  
+
* Shure MX202i Microphone                        
*:[[File:PigTail.JPG|60x80px]]
+
* S2 TT20 Torx security bit
* Shure MX202i Microphone  
+
* Wire Stripper  
*:[[File:MX202i.JPG|60x80px]]                         
 
* Starbit Security Driver
 
* Wire Stripper  
 
*:[[File:Wire_Stripper_and_Starbit_Driver.JPG|60x80px]] 
 
 
* 1/2" paddle bit
 
* 1/2" paddle bit
 
* 1 blank single gang wall plate  
 
* 1 blank single gang wall plate  
*:[[File:Blankplate.JPG|60x80px]]
+
* Tap-Cons (if mounting to concrete) (3/16")
* Toggle Bolts (If mounting to drop ceiling tile)  
+
* Screws and Anchors (3/16")
*:[[File:Toggle_Bolts.JPG|60x80px]]
+
* Toggle Bolts (If mounting to drop ceiling tile, mic mount) (3/16")  
 
* Drill bit and drill  
 
* Drill bit and drill  
*:[[File:Drill_and_Brill_Bits.JPG|60x80px]]
 
 
* Phillips head drill bit or Phillips head screwdriver
 
* Phillips head drill bit or Phillips head screwdriver
* Small Flat head screwdriver  
+
* Small Flat head screwdriver (#3)  
*:[[File:Small_Flathead_Screwdriver.JPG|60x80px]]  
+
* Shielded Stranded 22/2 + ground Wire  
* 22/2 Gauge Wire  
+
* Razor / box cutter
*:[[File:Audio_Cable.JPG|60x80px]]
 
* Razor  
 
*:[[File:Razor_Box_Cutter.jpg|60x80px]]
 
 
* B-Connectors
 
* B-Connectors
*:[[File:BCONN.png|60x80px]]
 
 
* Drywall Saw  
 
* Drywall Saw  
*:[[File:DryWall_Saw.JPG|60x80px]]
+
* Wind Screen (Inside MX202i kit)  
*Wind Screen (Inside MX202i Box)  
+
* Rubber Stopper (Inside MX202i kit)  
*:[[File:Mic_Windscreen.JPG|60x80px]]
+
* 4 pin XLR-M to XLR-M Adapter (Inside MX202i kit)
*Rubber Stopper (Inside MX202i Box)  
 
*:[[File:Mic_Rubber.JPG|60x80px]]
 
*4 pin XLR-M to XLR-M Adapter (Inside MX202i Box)
 
*:[[File:Shure_Adapter.JPG|60x80px]]
 
 
 
==Installation Instructions==
 
 
 
If using a recessed mount.
 
#Locate the network drop that is ran back to the POE switch. (If the switch does not have POE, you will need to insert a POE injector back at the network closet.)
 
#Using the instructions included in the Axis T94P01L box, use the razor to cut a hole into the drop ceiling tile and assemble the holding bracket for the camera. Mount bracket to drop ceiling. 
 
#:[[File:P5635 Mount assembled.jpg|500x400px]]
 
#Remove the dome from the M5525. The 22/12 pigtail and network cable should already be pre-docked in the camera. If not, you'll have to open the M5525, run the network drop through the mounting bracket and plug it in. (If the camera has both the pigtail and the network cable, simply run them both through the bracket into the ceiling.)
 
#Use the screws included with the mounting bracket to affix the M5525 to the recessed mount. Reattach the dome. Then affix the mounting disc to cover the ceiling tile.
 
#Cut 2 lengths of 22/2 cable long enough to go from the M5525 pigtail to the STM-1. One is for audio; the other is to power the STM-1.
 
#Strip the jacket and wire shielding about 1/2" to expose the wires. Connect the cable for power (Red to red, Black to black). Connect the cable for audio (red to yellow; black to white).
 
 
 
If mounting flush to a ceiling tile.
 
#Locate the network drop that is ran back to the POE switch. (If the switch does not have POE, you will need to insert a POE injector back at the network closet.)
 
#Remove the dome from the M5525.
 
#Make marks on our ceiling tile where our toggle bolts will go, and a place where our cables will be run.
 
#Carefully use a blade to cut a hole in the tile to run cables.
 
The 22/12 pigtail and network cable should already be pre-docked in the camera. If not, you'll have to open the 5525, run the network drop through the ceiling tile and plug it in. (If the camera has both the pigtail and the network cable, simply run them both through the tile.)
 
#Use the toggle bolts to secure the camera to the ceiling tile. Reattach the camera dome.
 
#Cut 2 lengths of 22/2 cable long enough to go from the M5525 pigtail to the STM-1. One is for audio; the other is to power the STM-1.
 
#Strip the jacket and wire shielding about 1/2" to expose the wires. Connect the cable for power (Red to red, Black to black). Connect the cable for audio (red to yellow; black to white).
 
 
 
 
 
==Connecting the STM-1==
 
 
 
#Connect one end of the 1 inch 22/2 cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
 
#:[[File:Phantom PWR STM.JPG|400x300px]]
 
#Connect the other end of the 22/2 we ran for power to the PWR terminals (Red to +, Black to the other terminal) of the STM-1.
 
#:[[File:STM_Powered_Connected.JPG|400x300px]]
 
#Connect the cable we ran for audio to the HI-Z OUTPUT terminals (Red to +, Black to ground) of the STM-1.
 
#We will need another length of 22/2 cable intended for your microphone; connect it to the input terminals of the STM-1 (Red to +, Black to -, ground to the ground terminal). Using the Velcro that comes with the STM-1, attach the STM-1 to the wall above drop ceiling hidden from sight.
 
(NOTE; If there are 2 cameras in the room, duplicate these steps to get to the 2nd camera. LO-Z output can feed 2 cameras, but no more.
 
  
==Connecting and Mounting the Microphone==
+
{{M5525 Installation Instructions}}
  
#Strip the jacket of the XLR pigtail revealing the red, black and common (silver) cables inside. Strip away a portion of the red and black cables inside the pigtail, revealing the copper wire inside. (This is typically already done before shipment from the office.) At the end of the 22/2 cable (connected to the STM-1 input), twist the wires together with the pigtail (red to red, black to black, common to common). Secure these with B-Connectors (See Pictures). Repeat this process if necessary for 2 microphones.
+
{{Connecting The Microphone Shure MX202i STM1}}
#:[[File:Audio spliced with pigtail.JPG|400x300px]] [[File:Pigtail_Splice_with_B_Connectors.JPG|400x300px]]
 
#Drill a hole into the center of the single gang plate using the ½” paddle bit, and a hole into the desired location for the microphone on your drop ceiling tile with a 1" paddle bit. Then secure this single gang plate to the desired location of the microphone on your drop ceiling tile using a pair of toggle bolts.
 
#:[[File:Plate_Mounted_to_Ceiling.JPG|400x300px]]
 
#Run your MX202i through the ½” hole in the ceiling tile and single gang plate.  Connect the 4 Pin XLR-F end of the MX202i to the 4 pin XLR-M adapter. Next, connect the XLR-F (that is ran back to the STM-1) to the XLR-M of the adapter. Use the rubber stopper to plug the ½” hole in the single gang plate.
 
#Lastly, adjust the length of the cable of the microphone to your desired length, hiding the remainder in the ceiling near the STM-1. Attach the windscreen to the MX202i.
 
#:[[File:Mic hanging from ceiling.JPG|400x300px]]
 

Latest revision as of 10:46, 18 May 2020

Wiring Diagram

Click to Expand

Select Optional Second Camera

AXIS Cam.png Axis P3235

AXIS Cam.png Axis P3245

AXIS Cam.png Axis P3364/P3365

AXIS Cam.png Axis P3374/P3375

AXIS Cam.png Axis Axis F41

AXIS Cam.png Axis P5414/P5415

AXIS Cam.png Axis Axis M5525

AXIS Cam.png Axis Axis P5635

AXIS Cam.png Axis P5655

AXIS Cam.png Axis V5914/V5915

AXIS Cam.png Axis Q8414

Required Parts And Tools

  • Axis M5525
  • AXIS T94P01L Recessed Mount
  • RDL STM-1
  • Female XLR Pigtail
  • Shure MX202i Microphone
  • S2 TT20 Torx security bit
  • Wire Stripper
  • 1/2" paddle bit
  • 1 blank single gang wall plate
  • Tap-Cons (if mounting to concrete) (3/16")
  • Screws and Anchors (3/16")
  • Toggle Bolts (If mounting to drop ceiling tile, mic mount) (3/16")
  • Drill bit and drill
  • Phillips head drill bit or Phillips head screwdriver
  • Small Flat head screwdriver (#3)
  • Shielded Stranded 22/2 + ground Wire
  • Razor / box cutter
  • B-Connectors
  • Drywall Saw
  • Wind Screen (Inside MX202i kit)
  • Rubber Stopper (Inside MX202i kit)
  • 4 pin XLR-M to XLR-M Adapter (Inside MX202i kit)

Installation Instructions

Disassemble Camera

  1. Using the T20 bit , remove the dome from the M5525
    5525NoDome.jpg
  2. Remove the yellow packing foam.
  3. Using the T20 bit, remove the camera from the mounting plate
    5525disassembled.jpg

Recessed Mount instructions

  1. Locate the network drop above the ceiling either being a male Ethernet end (service loop) or a biscuit jack. This will have been ran back to the POE switch.
    Note: If the switch does not have POE, a POE injector will need to be installed at the network closet.
  2. Using the instructions included in the Axis T94P01L box, use the razor to cut a hole into the drop ceiling tile, and assemble the holding bracket for the camera.
  3. Mount bracket to drop ceiling.
    P5635 Mount assembled.jpg
    Note: The 22/12 pigtail and network cable should already be pre-docked in the camera. If not, you'll have to open the M5525, run the cat 5 cable and pigtail through the mounting bracket and plug it in. (If the camera has both the pigtail and the network cable, simply run them through the bracket above the ceiling.)
  4. Use the screws included with the mounting bracket to affix the M5525 to the recessed mount.
  5. Reattach the dome. Then affix the mounting disc to cover the ceiling tile.
  6. Cut 2 lengths of 22/2 cable long enough to go from the M5525 pigtail to the Verifact A. One is for audio; the other is to power the microphone.
  7. Strip the jacket and wire shielding about 1/2" to expose the wires.
    • Connect the cable for power to the pigtail with B-connectors (Red to red, Black to black). Connect the cable for audio (red to yellow; black to white).

Drop Ceiling Mounting Instructions

  1. Locate the network drop above the ceiling either being a male Ethernet end (service loop) or a biscuit jack.
    Note: This will have been ran back to the POE switch. If the switch does not have POE, a POE injector will need to be installed at the network closet.
  2. Make marks on the ceiling tile where the toggle bolts will go, and a place from where the cables will be run.
  3. Carefully use a blade to cut a hole in the tile to run cables.
    DropCwiringHole1.jpg
    Note: The wiring hole should be cut such that it can be hidden by the camera dome.
  4. Use the toggle bolts to secure the mounting plate to the ceiling tile.
    5525DropCplate.jpg
  5. Using the T20 bit, attach the camera to the mounting plate and run cables through ceiling tile
    5525DropCwithCam.jpg DropCwiringHole2.jpg
  6. Reattach the camera dome.
    5525dropCfinished.jpg

Drywall / Hard Ceiling Mounting Instructions

  1. Locate the network drop above the ceiling either being a male Ethernet end (service loop) or a biscuit jack.
    Note: This will have been ran back to the POE switch. If the switch does not have POE, a POE injector will need to be installed at the network closet.
  2. Using a stud finder, scan the mount location to ensure the camera is not mounted on a stud.
  3. Using a pencil, mark the four holes for the mount plate.
  4. Using a 3/16" drill bit, drill the marked locations
  5. Install anchors and attach the mount plate using screws and washers.
    5525mount.jpg 5525drywallAnchors.jpg
  6. Using a hole saw or paddle bit, cut a hole where cabling will pass through
    Note: Ensure the hole cut for cabling will be covered by the camera dome
    5525drywallWire.jpg
  7. Using glow rods or fish tape, fish the network drop or patch cable in addition to the two sections of 22/2 audio cable through the drywall.
  8. Using the appropriate screws, attach the mounting plate
  9. Using the T20 bit, attach the camera to the mount plate
    5525drywallPLate.jpg
  10. Using the T20 bit, reattach the camera dome
    5525drywallDomed.jpg


Connecting Wiring

  1. Cut 2 lengths of 22/2 cable long enough to go from the M5525 pigtail to the microphone. One will be for audio. One will be for power
    Note: The 22/12 pigtail and network cable should already be pre-docked in the camera. If not, open the M5525, run the cat 5 cable and pigtail through the mounting bracket and plug it in (If the camera has both the pigtail and the network cable, simply run them both through the tile.).
  2. Strip the jacket and wire shielding about 1/2" to expose the wires.
    • Connect the cable for power (Red to red, Black to black).
    • Connect the cable for audio (red to yellow; black to white).
    5525PigtailAudio.jpg

Connecting the STM-1

  1. Cut a short piece of 22/2 cable (approx. 1 inch). Strip the jacket and from the cable and remove all contents keeping only the red cable. On both ends of the red cable, strip off a piece of the jacket (See picture).
    Phantom Power Jumper.JPG
  2. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
    Phantom PWR STM.JPG
  3. Connect the cable ran for power to both PWR terminals (Red to +, Black to the other terminal) of the STM-1. Connect the other side to the IO phoenix connector (Red to 2, Black to 1).
  4. Connect the cable ran for audio to both HI-Z OUTPUT terminals (Red to +, Black to the other terminal) of the STM-1. Connect the other side to the audio in portion of the audio phoenix connector (Red to +, Black to –).
    Wired with power and audio.JPG
  5. Using the Velcro that comes with the STM-1, attach the STM-1 to the wall above drop ceiling hidden from sight.
  6. The microphone will be connected via the input terminals of the STM-1 (Red to +, Black to -, ground to the ground terminal).


(NOTE: If there are 2 cameras in the room, duplicate these steps to get to the 2nd camera. HI-Z output can feed 2 cameras, but no more. If there are 2 Shure MX202i Microphones, duplicate steps. An STM-1 can power and gather audio from 2 Shure 202i mics.)

Connecting and Mounting the Microphone

  1. Asses the drop ceiling to decide best mounting placement for the MX202i. Avoid tiles adjacent to HVAC or fire safety devices.
  2. Drill a hole into the center of the single gang plate using the ½” paddle bit (if not prefabricated).
  3. Measure center of the drop ceiling tile and drill a similar hole with the ½” paddle bit.
  4. Align the single gang plate to the location of the microphone on the drop ceiling tile using a pair of toggle bolts.
    Plate Mounted to Ceiling.JPG
  5. Run the MX202i through the ½” hole in the ceiling tile and single gang plate with the rubber stopper to secure the microphone in place and plugging the ½” hole .
  6. Adjust the length of the cable of the microphone to a desirable length, hiding the remainder in the ceiling near the STM-1. Attach the windscreen to the MX202i.
    Mx202i.jpg
  7. Run the XLR mini cable to the STM-1 location.
  8. Connect the connect the XLR mini to the 4 pin Male XLR adapter.
  9. Strip away a portion of the red and black cables inside the pigtail, revealing the copper wire inside.
    • The microphone will be connected via the input terminals of the STM-1 (Red to +, Black to -, ground to the ground terminal).
  10. Connect the female XLR to the Male XLR adapter