|
|
| (147 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| − | =Overview=
| + | [[Privacy Button 2020-Present|Privacy Button 2020-Present]] |
| − | The privacy switch is a customizable solution for placing the cameras connected to the Valt system in privacy mode. The instructions below will outline how to configure a privacy switch that will stay illuminated while the switch is in the off position. Flipping the switch to the on position will extinguish the light and engage privacy mode. The switch and LED are independent and the behavior can be customized. See the variations section at the bottom of this article for more information.
| |
| | | | |
| − | These instruction are written for use with a camera with 4 IO ports. Port 1 and 2 are reserved for use with the Valt Recording Start/Stop button.
| + | [[File:Privacy Button On.png|200px|link=Privacy Button 2020-Present|Click to Navigate to This Page]] |
| | | | |
| − | =Compatible Cameras=
| + | [[Privacy Switch 2013-2019|Privacy Switch 2013-2019]] |
| − | The privacy switch should be usable with any axis camera with at least one free input and one free output. To use with a camera that does not have 4 I/O ports, you will need to adjust the event rules.
| |
| | | | |
| − | * Axis P5514
| + | [[File:PrivSwitch.png|200px|link=Privacy Switch 2013-2019|Click to Navigate to This Page]] |
| − | * Axis P5515
| |
| − | * Axis P5414
| |
| − | * Axis P5415
| |
| − | * Axis F41
| |
| − | | |
| − | '''Warning: The privacy switch is not currently compatible with the Axis P3364.'''
| |
| − | | |
| − | =Required Parts and Tools=
| |
| − | * Single Pole Single Throw Switch
| |
| − | * LED (Instead of an LED you can use an illuminated switch, but it must be independent)
| |
| − | *:[[File:Privacy7.jpg|300x225px]]
| |
| − | * Mud Ring or Single Gang Box
| |
| − | * Face Plate
| |
| − | * Wire Cutters/Strippers
| |
| − | * 22/4 solid unshielded plenum
| |
| − | | |
| − | =Installation=
| |
| − | # Cut a hole in the wall where the privacy switch will be mounted.
| |
| − | # Inset the mud ring into the hole and attach it.
| |
| − | # Run 22/4 from the camera to the hole.
| |
| − | # Strip the outer insulation from both ends of the 22/4.
| |
| − | #: [[File:Privacy1.jpg|600x450px]]
| |
| − | # Strip approximately 1/4 inch of insulation off of each wire in the 22/4 on the camera side
| |
| − | #: [[File:Privacy2.jpg|600x450px]]
| |
| − | # Insert the wires into the IO connector on the camera according to the chart below.
| |
| − | #: [[File:Privacy3.jpg|600x450px]]
| |
| − | #: Pin 1: Green
| |
| − | #: Pin 2: Red
| |
| − | #: Pin 5: Yellow
| |
| − | #: Pin 6: Black
| |
| − | #:: ''See the chart at the end of this section for a direct mapping between the switch and I/O connector''
| |
| − | # Strip approximately 1/2 inch of insulation off each wire in the 22/4 on the switch side.
| |
| − | #: [[File:Privacy4.jpg|600x450px]]
| |
| − | # Splice the wires to the switch according to the chart below.
| |
| − | #: [[File:Privacy5.jpg|600x450px]]
| |
| − | #: Green - Switch
| |
| − | #: Yellow - Switch
| |
| − | #: Red - LED Positive
| |
| − | #: Black - LED Ground
| |
| − | #:: ''Connections should be soldered, or connected with B connectors''
| |
| − | #: [[File:Privacy6.jpg|600x450px]]
| |
| − | # Attach the switch to the mud ring.
| |
| − | <br />
| |
| − | '''Wiring Map'''
| |
| − | ::{|class="wikitable" style="text-align:center;border-style:solid;border-width:1px;"
| |
| − | !style="width:100px;" | I/O Privacy Switch
| |
| − | !Phoenix Connector
| |
| − | |-
| |
| − | |Switch | |
| − | |Pin 1
| |
| − | |-
| |
| − | | +
| |
| − | |Pin 2
| |
| − | |-
| |
| − | |Switch
| |
| − | |Pin 5
| |
| − | |-
| |
| − | | -
| |
| − | |Pin 6
| |
| − | |}
| |
| − | | |
| − | =Configuration=
| |
| − | Prior to configuring the cameras for use with the privacy switch, make sure that the cameras have already been set up with a valid IP address and are configured according to [[Camera Settings|Valt specifications]].
| |
| − | ==Fixed Camera==
| |
| − | ===Configure Camera===
| |
| − | ====Set Privacy Mask====
| |
| − | # Open a web browser
| |
| − | # Copy and paste the following link into the address bar. Replace '''''ipaddress''''' with the ip address of your camera.
| |
| − | #: http://'''''ipaddress'''''/axis-cgi/privacymask.cgi?action=add&name=mask1&width=100&height=100
| |
| − | # Press enter to submit the address
| |
| − | # The mask should now be created. You can verify this by browsing to the IP address of the camera. The live view should show a black screen.
| |
| − | #: [[File:Privacy8.png|480x260px]]
| |
| − | # Copy and paste the following link into the address bar. Replace '''''ipaddress''''' with the ip address of your camera.
| |
| − | #: http://'''''ipaddress'''''/axis-cgi/param.cgi?action=update&Image.I0.Overlay.MaskWindows.M0.Enabled=no
| |
| − | # This should disable the mask you created. You can verify this by browsing to the ip address of the camera. The live view should show a live view from the camera.
| |
| − | #: [[File:Privacy9.png|480x260px]]
| |
| − | ====I/O Ports====
| |
| − | # Open a web browser
| |
| − | # Navigate to the IP address of the camera.
| |
| − | # If prompted enter the username and password for the camera.
| |
| − | # Click on Setup in the upper right hand corner of the window.
| |
| − | #: [[File:Privacy10.png]]
| |
| − | # Click on System Options.
| |
| − | #: [[File:Privacy11.png]]
| |
| − | # Click on Ports & Devices
| |
| − | #: [[File:Privacy12.png]]
| |
| − | # Change I/O Port 4 to Output
| |
| − | #: [[File:Privacy13.png]]
| |
| − | # Click Save
| |
| − | ===Load Rules===
| |
| − | ==PTZ Camera==
| |
| − | ===Configure Camera===
| |
| − | ====Set Privacy Location====
| |
| − | ====Set Privacy Mask====
| |
| − | ====I/O Ports====
| |
| − | ===Load Rules===
| |
| − | | |
| − | =Multiple Cameras=
| |
| − | =Variations=
| |
