Difference between revisions of "Camera Settings"
IVSWikiBlue (talk | contribs) |
IVSWikiBlue (talk | contribs) |
||
| Line 1: | Line 1: | ||
The following camera settings should be enabled prior to adding the camera to the VALT system. | The following camera settings should be enabled prior to adding the camera to the VALT system. | ||
| − | 1) Browse to the camera address (you can find the camera address using the Axis | + | 1) Browse to the camera address (you can find the camera address using the Axis IP Utility application), and set the '''root''' password. |
[[File:100.jpg|800px]] | [[File:100.jpg|800px]] | ||
| − | 2) Click on the | + | 2) Click on the '''Setup''' link in the upper left corner, then go to '''Basic Setup''' -> '''Video Stream''' make sure '''Compression''' is set to 30 and '''Frame Rate''' is set to 30. |
[[File:140.jpg|800px]] | [[File:140.jpg|800px]] | ||
| − | 3) Click on the H.264 tab and change the GOP | + | 3) Click on the '''H.264''' tab and change the '''GOP Length''' to 20. |
[[File:P5414-E_GopLength.png|800px]] | [[File:P5414-E_GopLength.png|800px]] | ||
| − | 4) Click on the Audio tab. Check the | + | 4) Click on the '''Audio''' tab. Check the '''Enable Audio''' checkbox (ensure the audio format is set to '''AAC''') as shown below then press Save. |
[[File:141.jpg|800px]] | [[File:141.jpg|800px]] | ||
| − | 5) Click on the | + | 5) Click on the '''Audio Settings''' section (using Chrome) and ensure a signal is present, using the audio indicator. When no one is speaking audio should be '''-40''' to '''-30 db''', and when someone is speaking, audio should be '''-20''' to '''-5 db'''. |
[[File:155.jpg|800px]] | [[File:155.jpg|800px]] | ||
| − | 6) For proper I/O and | + | 6) For proper I/O and Talkback functionality when using cameras with Axis firmware version 5.70 or greater: |
| − | Under Settings --> System Options --> Security --> Users you will need to set Allow | + | Under '''Settings''' --> '''System Options''' --> '''Security''' --> '''Users''' you will need to set '''Allow Password''' type to '''Unencrypted Only''', as shown below. |
After this change, you will need to restart the camera. | After this change, you will need to restart the camera. | ||
[[File:5514.jpg|800px]] | [[File:5514.jpg|800px]] | ||
Revision as of 15:12, 3 May 2019
The following camera settings should be enabled prior to adding the camera to the VALT system.
1) Browse to the camera address (you can find the camera address using the Axis IP Utility application), and set the root password.
2) Click on the Setup link in the upper left corner, then go to Basic Setup -> Video Stream make sure Compression is set to 30 and Frame Rate is set to 30.
3) Click on the H.264 tab and change the GOP Length to 20.
4) Click on the Audio tab. Check the Enable Audio checkbox (ensure the audio format is set to AAC) as shown below then press Save.
5) Click on the Audio Settings section (using Chrome) and ensure a signal is present, using the audio indicator. When no one is speaking audio should be -40 to -30 db, and when someone is speaking, audio should be -20 to -5 db.
6) For proper I/O and Talkback functionality when using cameras with Axis firmware version 5.70 or greater:
Under Settings --> System Options --> Security --> Users you will need to set Allow Password type to Unencrypted Only, as shown below.
After this change, you will need to restart the camera.
