Difference between revisions of "Template:5655 Installation Instructions"
IVSWikiBlue (talk | contribs) (Created page with "==Installation Instructions== ===Mounting the Camera=== #Locate the network drop above the ceiling either being a male Ethernet end (service loop) or a biscuit jack. This wil...") |
IVSWikiBlue (talk | contribs) (→Installation Instructions) |
||
| Line 7: | Line 7: | ||
#Determine the location where the 5655 will be mounted and remove the ceiling tile | #Determine the location where the 5655 will be mounted and remove the ceiling tile | ||
#Measuring the ceiling mount bracket, note that there is a slight lip to the camera mount | #Measuring the ceiling mount bracket, note that there is a slight lip to the camera mount | ||
| − | #: [[File:5635ceiingMount1.jpg|link=https://ipivs.com/wiki/images/2/29/5635ceiingMount1.jpg]] | + | #: [[File:5635ceiingMount1.jpg|link=https://ipivs.com/wiki/images/2/29/5635ceiingMount1.jpg|200px]] |
#Find center of the ceiling tile and using a pencil, draw a circle approximately nine inches in diameter | #Find center of the ceiling tile and using a pencil, draw a circle approximately nine inches in diameter | ||
#Using a drywall saw, cut out the section of ceiling tile where the mount will be inserted | #Using a drywall saw, cut out the section of ceiling tile where the mount will be inserted | ||
| − | #: [[File:5635CelingMountInstalled.jpg|link=https://ipivs.com/wiki/images/6/61/5635CelingMountInstalled.jpg]] | + | #: [[File:5635CelingMountInstalled.jpg|link=https://ipivs.com/wiki/images/6/61/5635CelingMountInstalled.jpg|200px]] |
#Using a T20 bit, tighten the mounting arms of the ceiling mount | #Using a T20 bit, tighten the mounting arms of the ceiling mount | ||
| − | #: [[File:5635celingMountArm.jpg|link=https://ipivs.com/wiki/images/8/85/5635celingMountArm.jpg]] [[File:5635celingMountArmFasten.jpg|link=https://ipivs.com/wiki/images/8/83/5635celingMountArmFasten.jpg]] | + | #: [[File:5635celingMountArm.jpg|link=https://ipivs.com/wiki/images/8/85/5635celingMountArm.jpg|200px]] [[File:5635celingMountArmFasten.jpg|link=https://ipivs.com/wiki/images/8/83/5635celingMountArmFasten.jpg|200px]] |
#: ''Note:'' Ensure not to over tighten into the ceiling tile. | #: ''Note:'' Ensure not to over tighten into the ceiling tile. | ||
#Pass the Axis MultiCable C I/O and the Ethernet cable through the hole at the top of the camera mount | #Pass the Axis MultiCable C I/O and the Ethernet cable through the hole at the top of the camera mount | ||
| − | #: [[File:5635CamWire.jpg|link=https://ipivs.com/wiki/images/1/1f/5635CamWire.jpg]] | + | #: [[File:5635CamWire.jpg|link=https://ipivs.com/wiki/images/1/1f/5635CamWire.jpg|200px]] |
#Connect cables to their respective ports | #Connect cables to their respective ports | ||
| − | #: [[File:5635CamWireConnect.jpg|link=https://ipivs.com/wiki/images/0/07/5635CamWireConnect.jpg]] | + | #: [[File:5635CamWireConnect.jpg|link=https://ipivs.com/wiki/images/0/07/5635CamWireConnect.jpg|200px]] |
#Before locking the 5635 to the mounting posts in the ceiling mount, ensure that the safety cable is attached to the camera | #Before locking the 5635 to the mounting posts in the ceiling mount, ensure that the safety cable is attached to the camera | ||
| − | #: [[File:5635safteyWire.jpg|link=https://ipivs.com/wiki/images/8/83/5635safteyWire.jpg]] [[File:5625safteyPost.jpg|link=https://ipivs.com/wiki/images/1/1a/5625safteyPost.jpg]] | + | #: [[File:5635safteyWire.jpg|link=https://ipivs.com/wiki/images/8/83/5635safteyWire.jpg|200px]] [[File:5625safteyPost.jpg|link=https://ipivs.com/wiki/images/1/1a/5625safteyPost.jpg|200px]] |
#Insert the camera into the ceiling mount and twist until locked in place securely | #Insert the camera into the ceiling mount and twist until locked in place securely | ||
| − | #: [[File:5625CameraInstalled.jpg|link=https://ipivs.com/wiki/images/6/63/5625CameraInstalled.jpg]] | + | #: [[File:5625CameraInstalled.jpg|link=https://ipivs.com/wiki/images/6/63/5625CameraInstalled.jpg|200px]] |
#Using a T20 bit, secure the dome ring to the camera mount | #Using a T20 bit, secure the dome ring to the camera mount | ||
| − | #: [[File:5635complete.jpg|link=https://ipivs.com/wiki/images/4/42/5635complete.jpg]] | + | #: [[File:5635complete.jpg|link=https://ipivs.com/wiki/images/4/42/5635complete.jpg|200px]] |
#Carefully return the ceiling tile to its location | #Carefully return the ceiling tile to its location | ||
| Line 35: | Line 35: | ||
#*Audio will be connected to the "In" on the audio terminal block - Red to +, Black to - | #*Audio will be connected to the "In" on the audio terminal block - Red to +, Black to - | ||
#*Power will be connected to the I/O terminal block - Red to to 2, Black to 1 | #*Power will be connected to the I/O terminal block - Red to to 2, Black to 1 | ||
| − | #: [[File:5635MulitCableConnect.jpg|link=https://ipivs.com/wiki/images/2/2e/5635MulitCableConnect.jpg]] | + | #: [[File:5635MulitCableConnect.jpg|link=https://ipivs.com/wiki/images/2/2e/5635MulitCableConnect.jpg|300px]] |
Latest revision as of 10:33, 27 August 2020
Installation Instructions
Mounting the Camera
- Locate the network drop above the ceiling either being a male Ethernet end (service loop) or a biscuit jack. This will have been ran back to the POE switch.
- Note: If the switch does not have POE, a POE injector will need to be installed at the network closet.
- Remove Axis T94A02L kit from packaging. This will include the mounting bracket and the camera dome ring.
- Determine the location where the 5655 will be mounted and remove the ceiling tile
- Measuring the ceiling mount bracket, note that there is a slight lip to the camera mount
-
- Find center of the ceiling tile and using a pencil, draw a circle approximately nine inches in diameter
- Using a drywall saw, cut out the section of ceiling tile where the mount will be inserted
-
- Using a T20 bit, tighten the mounting arms of the ceiling mount
-
- Note: Ensure not to over tighten into the ceiling tile.
-
- Pass the Axis MultiCable C I/O and the Ethernet cable through the hole at the top of the camera mount
-
- Connect cables to their respective ports
-
- Before locking the 5635 to the mounting posts in the ceiling mount, ensure that the safety cable is attached to the camera
-
- Insert the camera into the ceiling mount and twist until locked in place securely
-
- Using a T20 bit, secure the dome ring to the camera mount
-
- Carefully return the ceiling tile to its location
Note: If not using drop ceiling, use alternate instructions inside of the box for mounting to a hard ceiling.
Connecting Wiring
- Begin but cutting two lengths of 22/2. Ensure they are long enough to reach the microphone location. One will be for audio signal. One will be for power.
- Strip the jacket off the 22/2, revealing the red, black, and common (bare wire) on both sides of the cable.
- Remove the string and plastic casings covering the red and black cables.
- Strip the red and black jackets off the wire exposing the copper. Cut copper evenly on both ends. Remove ground.
- At the Axis MultiCable C I/O, connect the ends of 22/2
- Audio will be connected to the "In" on the audio terminal block - Red to +, Black to -
- Power will be connected to the I/O terminal block - Red to to 2, Black to 1
