Template:M5525 Installation Instructions
Contents
Installation Instructions
Disassemble Camera
- Using the T20 bit , remove the dome from the M5525
-
- Remove the yellow packing foam.
- Using the T20 bit, remove the camera from the mounting plate
-
Recessed Mount instructions
- Locate the network drop above the ceiling either being a male Ethernet end (service loop) or a biscuit jack. This will have been ran back to the POE switch.
- Note: If the switch does not have POE, a POE injector will need to be installed at the network closet.
- Using the instructions included in the Axis T94P01L box, use the razor to cut a hole into the drop ceiling tile, and assemble the holding bracket for the camera.
- Mount bracket to drop ceiling.
- Note: The 22/12 pigtail and network cable should already be pre-docked in the camera. If not, you'll have to open the M5525, run the cat 5 cable and pigtail through the mounting bracket and plug it in. (If the camera has both the pigtail and the network cable, simply run them through the bracket above the ceiling.)
- Use the screws included with the mounting bracket to affix the M5525 to the recessed mount.
- Reattach the dome. Then affix the mounting disc to cover the ceiling tile.
- Cut 2 lengths of 22/2 cable long enough to go from the M5525 pigtail to the Verifact A. One is for audio; the other is to power the microphone.
- Strip the jacket and wire shielding about 1/2" to expose the wires.
- Connect the cable for power to the pigtail with B-connectors (Red to red, Black to black). Connect the cable for audio (red to yellow; black to white).
Drop Ceiling Mounting Instructions
- Locate the network drop above the ceiling either being a male Ethernet end (service loop) or a biscuit jack.
- Note: This will have been ran back to the POE switch. If the switch does not have POE, a POE injector will need to be installed at the network closet.
- Make marks on the ceiling tile where the toggle bolts will go, and a place from where the cables will be run.
- Carefully use a blade to cut a hole in the tile to run cables.
-
- Note: The wiring hole should be cut such that it can be hidden by the camera dome.
-
- Use the toggle bolts to secure the mounting plate to the ceiling tile.
-
- Using the T20 bit, attach the camera to the mounting plate and run cables through ceiling tile
-
- Reattach the camera dome.
-
Drywall / Hard Ceiling Mounting Instructions
- Locate the network drop above the ceiling either being a male Ethernet end (service loop) or a biscuit jack.
- Note: This will have been ran back to the POE switch. If the switch does not have POE, a POE injector will need to be installed at the network closet.
- Using a stud finder, scan the mount location to ensure the camera is not mounted on a stud.
- Using a pencil, mark the four holes for the mount plate.
- Using a 3/16" drill bit, drill the marked locations
- Install anchors and attach the mount plate using screws and washers.
- Using a hole saw or paddle bit, cut a hole where cabling will pass through
- Note: Ensure the hole cut for cabling will be covered by the camera dome
- Using glow rods or fish tape, fish the network drop or patch cable in addition to the two sections of 22/2 audio cable through the drywall.
- Using the appropriate screws, attach the mounting plate
- Using the T20 bit, attach the camera to the mount plate
-
- Using the T20 bit, reattach the camera dome
-
M5525 Installation Instructions
1. Locate the AXIS T91E61 Wall Mount.
- This is the recommended wall mount by IVS. Verify the model of your mount here.
2. Locate the AXIS T94A01D Pendant Kit.
3. Connect the two parts and tighten them together by hand.
4. Continue tightening, by hand, until you cannot rotate the pendant kit anymore.
5. Using a T20 bit, tighten down the screw located inside the pendant kit.
6. Locate the mounting plate.
- This part comes packed with the AXIS M5525.
7. Take the camera disk and line up the 3 pegs on the top with the three holes on the pendant kit.
8. Put the pegs in the holes and rotate the disk counter clockwise until the pieces prevent you from turning more.
9. Using a T30 bit, tighten the three screws on top of the pendant kit, securing it to the camera disk.
10. Take the M5525 and plug the ethernet cable into its respective jack on the camera. The jack will be listed "PoE".
- Please note that only cameras prepared by IVS will have the pigtail wire connected to the camera. To learn more click here
11. Remove the rubber grommets from the base of the camera.
12. Run the cables through the holes where the grommets were.
- Note that each wire should be in its own hole.
13. Once the camera in the base, locate the four screws attached the camera and tighten them using a T20 bit.
14. Take the assembled wall mount and run the wires (that are attached to the camera) through the wall mount. Match the base of the camera to the bottom of the disc so that the holes for the screws align, allowing the camera to sit comfortably on the mount.
15. The camera will naturally sit on the base when everything is aligned properly.
16. Take the screws provided with the camera, located in the small box, and secure the camera to the mount using all 4 screws.
17. Place the dome back on the camera, making sure to align the plastic of the dome to match the plastic on the mount.
18. Use a T20 to secure the dome to the camera.
Connecting Wiring
- Cut 2 lengths of 22/2 cable long enough to go from the M5525 pigtail to the microphone. One will be for audio. One will be for power
- Note: The 22/12 pigtail and network cable should already be pre-docked in the camera. If not, open the M5525, run the cat 5 cable and pigtail through the mounting bracket and plug it in (If the camera has both the pigtail and the network cable, simply run them both through the tile.).
- Strip the jacket and wire shielding about 1/2" to expose the wires.
- Connect the cable for power (Red to red, Black to black).
- Connect the cable for audio (red to yellow; black to white).
