Privacy Button 2020-Present

From IVS Wiki
Revision as of 10:09, 13 November 2020 by IVSWikiBlue (talk | contribs)
Jump to: navigation, search

Overview

The privacy switch is a customizable solution for placing the cameras connected to the VALT system in privacy mode. The instructions below will outline how to configure a privacy switch that will light up while the switch is engaged. Disengaging the switch will extinguish the light and exit privacy mode.


Compatible Cameras

The privacy switch should be usable with any AXIS camera with at least one free input and one free output. The camera must be running firmware version 5.50 or higher.

  • Axis P5514
  • Axis P5515
  • Axis P5414-E
  • Axis P5415-E
  • Axis F41
  • Axis P3364/65*
  • Axis P3374/75-V*
  • Axis P3235-LVE*
  • Axis Q8414-LVS*
  • Axis M5525-E
  • Axis P5635 MKII


* These cameras have 4-pin I/O phoenix connectors, which means they only have 2 I/O ports. They can only be used with a single ancillary device (ie: Button OR privacy switch).

Required Parts and Tools

  • VALT Privacy Button and Face Plate
    PrivacySwitch2.jpg
  • Mud Ring or Single Gang Box
  • Wire Cutters/Strippers
  • 22/4 solid unshielded plenum
  • Jab Saw (used to cut hole)
  • Wire fishing poles or tape
  • B Connectors

Wire Diagrams by Camera

AXIS Cam.png Axis P3235

AXIS Cam.png Axis P3245

AXIS Cam.png Axis P3364/P3365

AXIS Cam.png Axis P3374/P3375

AXIS Cam.png Axis F41

AXIS Cam.png Axis P5414/P5415

AXIS Cam.png Axis M5525

AXIS Cam.png Axis P5635

AXIS Cam.png Axis P5655

AXIS Cam.png Axis V5914/V5915

AXIS Cam.png Axis Q8414


Installation Instructions

  1. Cut a hole in the wall where the privacy switch will be mounted.
  2. Insert the mud ring into the hole, and attach it.
  3. Run 22/4 from the camera to the hole.
  4. Strip the outer insulation from both ends of the 22/4.
    Privacy1.jpg
  5. Strip approximately 1/4 inch of insulation off of each wire in the 22/4 on the camera side
    Privacy2.jpg
  6. Insert the wires into the IO connector on the camera according to the chart below.
    Privacy3.jpg
    Pin 1: Green
    Pin 2: Red
    Pin 5: Yellow
    Pin 6: Black
    See the chart at the end of this section for a direct mapping between the switch and I/O connector
  7. Strip approximately 1/2 inch of insulation off each wire in the 22/4 on the switch side.
    Privacy4.jpg
  8. Splice the wires to the switch according to the chart below.
    PrivacyButton StartButton.png
    Connections should be connected with B connectors
  9. Attach the switch to the mud ring.


Wiring Map

Privacy Switch Lead Color Phoenix Connector
Switch Green Pin 1
+ Red Pin 2
Switch Yellow Pin 5
- Black Pin 6

Configuration

Prior to configuring the cameras for use with the privacy switch, make sure that the cameras have already been set up with a valid IP address, and are configured according to VALT Specifications.

Load Rules

  • If you prefer to configure the camera for Privacy manually, skip to SET PRIVACY MASK.
  1. Download the camera rules, using the links below:
    P3364: https://ivs.box.com/shared/static/b4wbmbyzwi3laz030hb33lidsmz64btp.cfg
    Fixed: https://ivs.box.com/shared/static/wr8sx4oxruykuhpftj0o8ff80s3y7lap.cfg
    PTZ: https://ivs.box.com/shared/static/2yleyfngk6erpoxki06a1u1e84hxlmxd.cfg
  1. Open Access Device Manager.
  2. Click on the Add Device from Address icon or Add Devices from IP Range.
    Privacy14.png
  3. Enter the IP address of the camera or the IP range using a * for the last quartet if adding multiple.
    Privacy15.png
  4. Click OK.
  5. Enter the username and password for the camera(s).
    Privacy16.png
  6. Click OK.
  7. The camera(s) should now appear in the list of devices.
    Privacy18.png
  8. Right click on the camera(s), and select Configure Devices. Configure from the menu.
    Privacy19.png
  9. Click the Configuration File button.
    Privacy20.png
  10. Browse to where configuration file is saved, and select it.
    Privacy21.png
  11. Click Open.
  12. Click Next.
    Privacy23.png
  13. Click Finish.
  14. When the rules have successfully loaded, a message will display at the bottom of the window.
    Privacy24.png

Set Privacy Location for PTZ Camera

THIS IS SO MUCH FUCKING WORK BRAH If the camera is a PTZ, you need to set a Privacy Location.

  1. Open a web browser.
  2. Copy and paste the following link into the address bar. Replace ipaddress with the ip address of the camera:
    http://ipaddress/axis-cgi/com/ptzconfig.cgi?setserverpresetname=Privacy&home=yes
  3. Press Enter to submit the address.


Set Privacy Mask

This can be done through the API or through the web browser of the camera.

Via API

  1. Open a web browser.
  2. Copy and paste the following link into the address bar. Replace ipaddress with the ip address of the camera:
    http://ipaddress/axis-cgi/privacymask.cgi?action=add&name=mask1&width=100&height=100
  3. Press Enter to submit the address.
  4. The mask should now be created. This can verified by browsing to the IP address of the camera. The live view should show a black screen.
    Privacy8.png
  5. Copy and paste the following link into the address bar. Replace ipaddress with the ip address of the camera:
    http://ipaddress/axis-cgi/param.cgi?action=update&Image.I0.Overlay.MaskWindows.M0.Enabled=no
  6. This should disable the mask created. This can be verified by browsing to the IP address of the camera. The live view should show a live view from the camera.
    Privacy9.png

Via Web Interface

Perform these steps only if configuring the mask via API fails.

  1. Open a web browser.
  2. Navigate to the IP address of the camera.
  3. If prompted, enter the username and password for the camera.
  4. Click on Setup in the upper right hand corner of the window.
    Privacy10.png
  5. Click on Video & Audio.
    Privacy11.png
  6. Click on Privacy Mask.
    Privacy36.png
  7. Click Add.
  8. Enter Privacy in the Mask name field.
  9. Expand the box slowly using a mouse until it covers the entire image.
    Privacy37.png
  10. Click Save.
  11. Click on the Privacy mask just created.
    Privacy38.png
  12. Click Enable/Disable.


Add Recipient(s)

Some of the rules point to a recipient at a specific IP address, so the camera must have a recipient set up, even for itself. In the case of a room with multiple cameras, the master camera will need a recipient set up for all other cameras in the room as well.

  1. Click on Setup in the upper right hand corner of the window.
    Privacy10.png
  2. Click on Events.
  3. Click on Recipients.
  4. Click on Add.
    Add Self in the name field
    In Recipient, type 
http://127.0.0.1/axis-cgi/param.cgi

or 

http://'''''ipaddress'''''/axis-cgi/param.cgi
  1. Type in the login credentials for the camera.
    Click Test.
    Click Close.


Manual Set up of Privacy Rules

This is how to create the privacy rules if loading the config file doesn't work properly.

Update I/O Ports

  1. Open a web browser.
  2. Navigate to the IP address of the camera.
  3. If prompted, enter the username and password for the camera.
  4. Click on Setup in the upper right hand corner of the window.
    Privacy10.png
  5. Click on System Options.
    Privacy11.png
  6. Click on Ports & Devices.
    Privacy12.png
  7. Change I/O Port 2 to Output. For an F41, change I/O Port 4 to Output. For a camera who's ports do not alternate, simply rename the output "Output 2".
    Privacy13.png
  8. Click Save.

Privacy Rules for Fixed

Privacy Off Rules

Name Value
action update
Image.I0.Overlay.MaskWindows.M0.Enabled no
AudioSource.A0.InputGain 0
PTZ.Various.V1.PanEnabled true
PTZ.Various.V1.TiltEnabled true
PTZ.Various.V1.ZoomEnabled true
autofocus on


  • If during the course of audio testing, the cameras have been set to gain other than 0, you must also update the gain value in these rules.

PrivacyOff.png


Privacy On Rules

Name Value
action update
Image.I0.Overlay.MaskWindows.M0.Enabled yes
AudioSource.A0.InputGain mute
PTZ.Various.V1.PanEnabled false
PTZ.Various.V1.TiltEnabled false
PTZ.Various.V1.ZoomEnabled false

PrivacyOn.png


LED On

PrivacyLedOn.png


LED Off

PrivacyLedOff.png

Retrieved from "https://ipivs.info/wiki/index.php?title=Privacy_Button_2020-Present&oldid=7583"