Deprecated Page - Installing a VMWare Virtual Appliance

Download the OVF Template

1. Click on the link below to download the OVF Template for the Valt virtual appliance.

   VMWare 5.5: https://ivs.box.com/shared/static/t5rti7fl7h6szxxlytkjak7u9byllo0h.zip

   VMWare 6.0: https://ivs.box.com/shared/static/tf248uzr3qgdg1x4q9crvmgn7952keb1.zip

2. Extract the ValtVMWare.zip

Load the Template on vSphere

1. Open vSphere Client
2. Click on File

   

3. Select Deploy OVF Template from the menu.

   

4. Click on Browse

   

5. Browse to where you extracted the zip file.
6. Select the Valt.ovf file.
7. Click Open

   

8. Click Next

   

9. Click Next

   

10. Enter a name for your Valt appliance
11. Click Next

    

12. Select your disk provisioning

    Thin Provisioning Recommended

13. Click Next

    

14. Select the network the appliance should be connected to.
15. Click Next

    

16. Click Finish

Configure Virtual Hardware

1. Right click on the virtual machine in vSphere Client
2. Select Edit Settings from the menu

   

3. Adjust the memory and CPU of the appliance to support the number of cameras. The table below contains IVS' recommended specs.

Cameras	Cores	Memory
5	4	8 GB
15	8	16 GB
25	16	32 GB
50	32	64 GB

Click OK once all changes have been made.

You can also adjust the size of the data drive. The default size is 2 TB. If you adjust the size of the virtual drive, you will also need to adjust the size of the partition.

Add the USB Key to the VM (Optional)

There are two types of Wowza licenses. By default IVS will provide a Wowza license key and a USB key. The steps below are to add the USB key to the VM. If you want to use the VM in a highly available environment, IVS can provide a license only key that does not require a USB key. Please make sure to request this at the time of order.

1. Right click on the virtual machine in vSphere Client

   

2. Select Edit Settings from the menu

   

3. Click Add

   

4. Select USB Controller
5. Click Next

   

6. Select EHCI+UHCI
7. Click Next

   

8. Click Finish
9. Click Add

   

10. Select USB Controller
11. Click Next

    

12. Select xHCI
13. Click Next

    

14. Click Finish
15. Click Add

    

16. Select USB Device
17. Click Next

    

18. Select Future Devices HID UNIKEY
19. Click Next

    

20. Click Finish
21. Click OK

Configure IP Address

You must complete these steps even if you have already specified an IP address for the server or want to use DHCP. This will configure the Valt software with the correct IPs

For more in depth information on network configuration options, see the Valt Command Line Menu page.

1. Access the Valt Server Command Line Menu.

   This menu is presented automatically at the Valt server terminal. It can also be accessed via ssh by running the following command from the prompt:

   sudo /usr/local/valt/bin/Menu

   

2. Enter Option 1 for Network Configuration

   

3. Enter Option 2 for Set IPs

   

4. Select your interface from the options listed.

   

5. Select Static or DHCP.

   For this example we will select DHCP

6. 
7. Type Y when to configure this interface for client access.
8. 
9. Enter the IP Address of the interface when prompted.

IP Address changes will not take effect until the server has been rebooted.

Install the Wowza Streaming Engine License

1. Open a web browser and navigate to http://IPAddress:8088

   Replace IPAddress with the IP Address of the server.

   

2. Click Skip Intro.

   

3. Sign in using the username and password defined earlier for Wowza.

   

4. Copy and paste the Wowza License Key into the box provided.

   If you are not prompted for a key:

   1. Click on the Server tab
   2. Click the Edit button.
   3. Copy and paste the Wowza License Key into the box provided.

   If you were provided with a USB key by IVS, the USB key must already be inserted into the appliance.

5. Click Save
6. You will be returned to the sign in page.

   If you are not returned to the sign in page, click Sign Out in the upper right corner of the page.

7. Sign back in to the Wowza web console.

   If you are returned to the license page, the license was not accepted.

   • Check to make sure the USB key is inserted.
   • Check to make sure there are no typos or leading or trailing spaces.
   • Reboot the server

   

8. Click on Performance Tuning > Java Settings

   

9. Click Edit

   

10. Select Production Level
11. Click Save

    

12. You will be prompted to restart, click Restart Now

Install the Valt Camera License

1. Access the Valt Server Command Line Menu.

   This menu is presented automatically at the Valt server terminal. It can also be accessed via ssh by running the following command from the prompt:

   sudo /usr/local/valt/bin/Menu

   

2. Enter Option 3 for Valt Configuration

   

3. Enter Option 1 for Install License

   

4. Enter your license provided by IVS and press enter.
5. You will be returned to the menu.

Set the Timezone

1. Connect to the Valt appliance via SSH or from the terminal menu, exit to the shell.
2. From command line type sudo dpkg-reconfigure tzdata

   

3. Select your country

   

4. Select your Time Zone

   

5. From command line type sudo service apache2 restart
6. From command line type sudo service WowzaStreamingEngine restart

   

Accessing the Valt Server

To access the system open up a web browser (Chrome, Firefox, Internet Explorer, Safari) and point it to the DNS name (example: http://video.myschool.edu) or IP address (example: http://192.168.0.99) of the Valt server. Note the default IP address the servers ship with is 192.168.0.99. For all non-chrome browsers if adobe flash player is not already installed it will need to be. (http://get.adobe.com/flashplayer/)

Log into the system with the proper username and password. (default: “admin” “admin”)

Based on your login information you may have access to any of the following sections: Observe, Record, Schedule, Upload and Admin as shown below.