Installing an Axis P5414/P5415 with a Verifact A Microphone

Required Parts And Tools

• Axis P5415 or P5415
• T20 Torx security bit
• T10 Torx Security bit
• Wire Stripper
• Wall Dogs (if mounting to concrete) (7/8")
• Screws and Anchors (7/8")
• 1/2" paddle bit
• Toggle Bolts (If mounting mic to drop ceiling tile) (3/16")
• Drill bit and drill
• Phillips head drill bit or Phillips head screwdriver
• Small Flat head screwdriver (#3)
• Hole Saw (2")
• B Connectors
• Stud Finder
• Cat5/6 Patch Cable (7ft-15ft recommended)
• Shielded Stranded 22/2 +ground Wire
• Fish Tape or Glow Rods
• Louroe Verifact A Microphone

Installation Instructions

1. Locate the network drop above the ceiling either being a male Ethernet end (service loop) or a biscuit jack. This will have been ran back to the POE switch providing High POE

   Note: High POE requires up to 37W for PTZ functions. If the switch does not have High POE, a POE injector will need to be installed at the network closet.

2. Using a stud finder, ensure there aren’t any studs where the camera will be mounted.

Disassembling the Camera

1. Remove the P5414/P5415 camera from its base with the T20 bit.
2. Using a small Phillips head screwdriver, remove the plastic ring around the base of the camera dome.
3. Using the T10 bit, remove the camera dome and remove the protective foam.
4. Reattach the dome and snap the plastic ring back into place.

Mounting the Camera

1. While holding the camera base plate where it will be mounted, use a pencil to mark the 4 areas on the wall where the screws will be located. Also mark the opening where the any cabling will pass through (see image below).

   

2. Using the drill bit, drill the 4 screw marks and insert mounting anchors.
3. Using the hole saw (recommended size 2” inches or less), drill a hole into the area where cables will pass through.
4. Using the hole saw, drill a hole above the drop ceiling in line with the hole drilled where the camera will be mounted.

   Note: If there isn’t any drywall above the ceiling, adjust accordingly to your circumstance.

5. Using glow rods or fish tape, fish the network drop and 2 sections of 22/2 audio cable through the drywall.

   Note: The sections of audio cable should be long enough to reach the destination where the STM-1 preamp will be mounted in ther drop ceiling. One will be for audio to the camera; the other will be to power the STM-1.

6. Mount the Axis P5414/5415 base to the wall using the screws associated with the anchors.
7. Remove the middle rubber piece on the camera base and run the network drop and any other cabling through this hole.

   

8. Strip the jacket off the 2 runs of 22/2, revealing the red, black, and common (bare wire). Remove the string and plastic casings covering the red and black cables. Strip the red and black jackets off the wire exposing the copper. Cut copper evenly on both ends (See picture). On the cable for power, remove the common (bare wire) completely.

   

9. At the camera, connect the 22/2 for audio to the audio terminal block. Red to 3, Black to 1
10. Connect the 22/2 for power to the I/O terminal block. Red to 2, Black to 1

Connecting the Microphone

1. Drill a hole into the piece of ceiling tile that the Louroe Verifact-A will be mounted to. Feed one end of the the 22/2 audio cable through the hole. Using toggle bolts, secure the microphone.
2. At the microphone, connect the 22/2 cables as follows: AUDIO: Red to B, Black to C POWER: Red to A, Black to C
3. At the camera, connect the 22/2 cables as follows: AUDIO: Red to 3, Black to 1 on audio terminal block, POWER: Red to 3, Black to 1 on I/O terminal block