Difference between revisions of "2 x 2 Configuration"

From IVS Wiki
Jump to: navigation, search
(→‎Tesira Software)
 
(11 intermediate revisions by the same user not shown)
Line 3: Line 3:
  
 
=Physical Wiring/Line Diagram=
 
=Physical Wiring/Line Diagram=
−
Again, we can use whichever inputs and outputs we’d like, so let’s use inputs 1&2 and outputs 1&2 to keep things simple. When we terminate our cables, the mics will go into Orange Inputs 1&2 and the audio line to the cameras will go into Black Outputs 1&2.  
+
Use inputs 1&2 and outputs 1&2 to keep things simple. When terminating the cables, the mics will go into Orange Inputs 1&2 and the audio line to the cameras will go into Black Outputs 1&2.  
  
−
[[File:Two_Config_Line_Diagram.png|link=https://ipivs.com/wiki/images/f/ff/Two_Config_Line_Diagram.png|500px]]
+
{{img | file = Two_Config_Line_Diagram.png | width=500px}}
  
 
=Tesira Software=
 
=Tesira Software=
  
 
==Connections==
 
==Connections==
−
# Once we've completed our physical connections, open the Tesira software and start building a configuration.  
+
# If the physical connections are complete, open the Tesira software and start building a configuration.  
−
# In this configuration we'll be using the following blocks. Add these blocks to the configuration:  
+
# In this configuration use the following blocks:  
 
#* TesiraFORTE CI block
 
#* TesiraFORTE CI block
 
#* Peak Meter x 3
 
#* Peak Meter x 3
Line 19: Line 19:
 
#* Matrix Mixer with at least 2 inputs and 2 outputs, with one extra output
 
#* Matrix Mixer with at least 2 inputs and 2 outputs, with one extra output
 
#Connect the blocks as follows:  
 
#Connect the blocks as follows:  
−
#* The Tesira Input block will already be connected to the AEC block, so connect the first peak meter to the Input block also. This will help us to be sure we have the proper levels set on the preamp.  
+
#* The Tesira Input block will already be connected to the AEC block, so connect the first peak meter to the Input block also. This will help ensure proper levels are set on the preamp.  
 
#* Connect the AEC block channels 1&2 to the Uber Filters.  
 
#* Connect the AEC block channels 1&2 to the Uber Filters.  
 
#* Send the Uber Filters to the Level Block.  
 
#* Send the Uber Filters to the Level Block.  
 
#* Send the Level Block to the Compressor and the second peak meter.  
 
#* Send the Level Block to the Compressor and the second peak meter.  
 
#* Send the Compressor to the Matrix Mixer.  
 
#* Send the Compressor to the Matrix Mixer.  
−
#* Connect output 1&2 from the mixer to port 1&2 on the Tesira Output block AND to the third peak meter. This way we can make sure to reach the right audio levels before we send it to the cameras.  
+
#* Connect output 1&2 from the mixer to port 1&2 on the Tesira Output block AND to the third peak meter. This will ensure the right audio levels are sent to the camera.  
−
#* Connect the extra output from the Matrix Mixer to the AEC reference. We will not need to activate the Automatic Echo Cancellation feature in this example. However, Tesira will not allow us to delete the AEC reference block for some reason. It also will not compile the configuration if any blocks are not connected (including the AEC reference block.) So, I’d recommend using an extra output from the mixer as a "dummy output" channel. We will not send any audio to this channel.  
+
#* Connect the extra output from the Matrix Mixer to the AEC reference. The Automatic Echo Cancellation feature will not be used in this example. However, the AEC reference block cannot be deleted from the configuration. It also will not compile the configuration if any blocks are not connected (including the AEC reference block.) So use the extra output from the mixer as a "dummy output" channel. Do not send any audio to this channel.  
  
  
−
When we're complete, our file should look something like this:  
+
When this is complete, the file should look something like this:  
−
 
 
−
[[File:Two_to_Two_Config.png]]
 
  
 +
{{img | file = Two_to_Two_Config.png}}
  
 
==Matrix Mixer==
 
==Matrix Mixer==
  
−
[[File:Two_to_Two_with_Mixer.png]]
+
{{img | file = Two_to_Two_with_Mixer.png}}
  
 
#The only difference between this configuration and the last, Simple Configuration with EQ and Compression, is the use of 2 input and 2 output channels.  
 
#The only difference between this configuration and the last, Simple Configuration with EQ and Compression, is the use of 2 input and 2 output channels.  
Line 44: Line 43:
  
 
For further insight about the other processing blocks and settings, refer back to the first configuration example, or click the image below:  
 
For further insight about the other processing blocks and settings, refer back to the first configuration example, or click the image below:  
−
[[File:Simple_Config.png|link=https://ipivs.com/wiki/Simple_Configuration#Processing_Blocks_in_Tesira]]
 
  
 +
{{img | file = Processing_Blocks_Page.png}}
  
 
==EQ and Compression==
 
==EQ and Compression==
  
−
For information on EQ settings and compression, refer to Simple Configuration with EQ and Compression, or click the link below:  
+
For information on EQ settings, or click the image below:  
−
[[File:One_Complex_Config.png|link:https://ipivs.com/wiki/Simple_Configuration_with_EQ_and_Compression#Processing_Blocks_in_Tesira]]
+
{{img | file = EQ_Page.png}}
 +
 
 +
 
 +
 
 +
For Compression parameters, click the image below:
 +
{{img | file = Compression_Page.png}}

Latest revision as of 10:14, 10 May 2022

Description/Objective

In this example, we will be connecting two microphones to two cameras in one room.

Physical Wiring/Line Diagram

Use inputs 1&2 and outputs 1&2 to keep things simple. When terminating the cables, the mics will go into Orange Inputs 1&2 and the audio line to the cameras will go into Black Outputs 1&2.

Two Config Line Diagram.png

Tesira Software

Connections

  1. If the physical connections are complete, open the Tesira software and start building a configuration.
  2. In this configuration use the following blocks:
    • TesiraFORTE CI block
    • Peak Meter x 3
    • Uber Filter x 2
    • Level Block with 2 channels
    • Compressor with 2 channels, "ganged mode" and "advanced curve"
    • Matrix Mixer with at least 2 inputs and 2 outputs, with one extra output
  3. Connect the blocks as follows:
    • The Tesira Input block will already be connected to the AEC block, so connect the first peak meter to the Input block also. This will help ensure proper levels are set on the preamp.
    • Connect the AEC block channels 1&2 to the Uber Filters.
    • Send the Uber Filters to the Level Block.
    • Send the Level Block to the Compressor and the second peak meter.
    • Send the Compressor to the Matrix Mixer.
    • Connect output 1&2 from the mixer to port 1&2 on the Tesira Output block AND to the third peak meter. This will ensure the right audio levels are sent to the camera.
    • Connect the extra output from the Matrix Mixer to the AEC reference. The Automatic Echo Cancellation feature will not be used in this example. However, the AEC reference block cannot be deleted from the configuration. It also will not compile the configuration if any blocks are not connected (including the AEC reference block.) So use the extra output from the mixer as a "dummy output" channel. Do not send any audio to this channel.


When this is complete, the file should look something like this:

Two to Two Config.png

Matrix Mixer

Two to Two with Mixer.png

  1. The only difference between this configuration and the last, Simple Configuration with EQ and Compression, is the use of 2 input and 2 output channels.
  2. Mixer: In this example, both mics and both cameras live in the same room, so both mics are sent to both cameras.


Processing Blocks in Tesira

For further insight about the other processing blocks and settings, refer back to the first configuration example, or click the image below:

Processing Blocks Page.png

EQ and Compression

For information on EQ settings, or click the image below: EQ Page.png


For Compression parameters, click the image below: Compression Page.png

Retrieved from "https://ipivs.info/wiki/index.php?title=2_x_2_Configuration&oldid=9148"