Difference between revisions of "Installing Overhead Speaker on Axis Cameras with STM-1"
IVSWikiBlue (talk | contribs) (Created page with "==Required Parts And Tools== * Axis P5414-E 100x100px * Amplified Overhead Speaker (Any speaker will due, however, we recommend the OWI-AMPR2SIC5 and will be...") |
IVSWikiBlue (talk | contribs) |
||
(3 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
==Required Parts And Tools== | ==Required Parts And Tools== | ||
− | * Axis P5414-E | + | * Axis P3364/65, F41, P1364/65, P8414, P5914/15, M5525, P5414/15-E, P5635 |
* Amplified Overhead Speaker (Any speaker will due, however, we recommend the OWI-AMPR2SIC5 and will be the speaker referenced in these instructions)[[File:In Ceiling Speakers.jpg|120x160px]] | * Amplified Overhead Speaker (Any speaker will due, however, we recommend the OWI-AMPR2SIC5 and will be the speaker referenced in these instructions)[[File:In Ceiling Speakers.jpg|120x160px]] | ||
+ | * Shure MX393 Boundary Mic | ||
+ | * RDL STM-1 Preamp | ||
+ | * F-XLR Tail | ||
* 22/2 audio cable [[File:Stripped 22 2 Wire.JPG|60x80px]] | * 22/2 audio cable [[File:Stripped 22 2 Wire.JPG|60x80px]] | ||
* Fish Tape or Glow Rod [[File:15-4-57-m-mid-flex-glow-rod-set-tools-to-k56415-to-k56415-19671-228x228.jpg|60x80px]] | * Fish Tape or Glow Rod [[File:15-4-57-m-mid-flex-glow-rod-set-tools-to-k56415-to-k56415-19671-228x228.jpg|60x80px]] | ||
Line 10: | Line 13: | ||
==Installation Instructions== | ==Installation Instructions== | ||
− | #Once your camera is installed, locate the | + | #Once your camera is installed, locate the power out from the camera. Decide where you will mount the STM-1, knowing your MX393 mic will need to reach it. |
− | # | + | #Place your MX393. Plug the mic into the F-XLR tail. The wires of the XLR will wire to the +, -, and ground Input on the STM-1. (You may want to splice a short length of 22/2 to make it easier to wire to the STM-1 terminals.) |
− | #Wire the red to the + and black to the - | + | #Cut a length of 22/2 from the STM-1 to the camera. Strip the jacket on both ends. Cut away the bare wire and plastic surround the cable inside. Strip away a small piece of the red and black jackets revealing the bare copper wire. |
− | # | + | #Wire one end to the power out on your camera. On the other end, wire the red to the + and black to the ground power terminals on the STM-1. |
− | + | #You will also need to cut a short piece of 22/2 cable (approx. 1 inch). Strip the jacket from the cable and remove all contents keeping only the red cable. On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal. | |
− | |||
− | |||
− | |||
+ | #In this step, you want to run your 22/2 cable from the camera to your AMP2SIC5, wiring your red wire to the + phoenix connection and black to the - connection of the LINE INPUT of the AMP2SIC5 (See pics). | ||
#Once audio is plugged in, locate your run 18/2 from the AMP2SIC5 to its designated power outlet. Test the talkback unit is working by activating the talkback function within the Valt Software by having a partner use their computer microphone to communicate with you. | #Once audio is plugged in, locate your run 18/2 from the AMP2SIC5 to its designated power outlet. Test the talkback unit is working by activating the talkback function within the Valt Software by having a partner use their computer microphone to communicate with you. | ||
[[File:Talkback Turn On.jpg|720x960px]] | [[File:Talkback Turn On.jpg|720x960px]] |
Latest revision as of 10:28, 19 April 2019
Required Parts And Tools
- Axis P3364/65, F41, P1364/65, P8414, P5914/15, M5525, P5414/15-E, P5635
- Amplified Overhead Speaker (Any speaker will due, however, we recommend the OWI-AMPR2SIC5 and will be the speaker referenced in these instructions)
- Shure MX393 Boundary Mic
- RDL STM-1 Preamp
- F-XLR Tail
- 22/2 audio cable
- Fish Tape or Glow Rod
- Electrical Tape
- Wire Stripper
Installation Instructions
- Once your camera is installed, locate the power out from the camera. Decide where you will mount the STM-1, knowing your MX393 mic will need to reach it.
- Place your MX393. Plug the mic into the F-XLR tail. The wires of the XLR will wire to the +, -, and ground Input on the STM-1. (You may want to splice a short length of 22/2 to make it easier to wire to the STM-1 terminals.)
- Cut a length of 22/2 from the STM-1 to the camera. Strip the jacket on both ends. Cut away the bare wire and plastic surround the cable inside. Strip away a small piece of the red and black jackets revealing the bare copper wire.
- Wire one end to the power out on your camera. On the other end, wire the red to the + and black to the ground power terminals on the STM-1.
- You will also need to cut a short piece of 22/2 cable (approx. 1 inch). Strip the jacket from the cable and remove all contents keeping only the red cable. On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
- In this step, you want to run your 22/2 cable from the camera to your AMP2SIC5, wiring your red wire to the + phoenix connection and black to the - connection of the LINE INPUT of the AMP2SIC5 (See pics).
- Once audio is plugged in, locate your run 18/2 from the AMP2SIC5 to its designated power outlet. Test the talkback unit is working by activating the talkback function within the Valt Software by having a partner use their computer microphone to communicate with you.