Difference between revisions of "Installing an Axis F41 and Axis F1005 sensor unit with a Louroe Verifact A Microphone"
IVSWikiBlue (talk | contribs) (→Installation Instructions) |
IVSWikiBlue (talk | contribs) |
||
| (37 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | {{Wirediagram F41 Verifact A}} | ||
| + | |||
==Required Parts And Tools== | ==Required Parts And Tools== | ||
| + | |||
* Axis F41 Main Unit | * Axis F41 Main Unit | ||
| − | |||
* Axis F1005 | * Axis F1005 | ||
| − | |||
* Axis F8001 | * Axis F8001 | ||
| − | |||
| − | |||
| − | |||
* 3.5mm (Male to Male) Audio Cable | * 3.5mm (Male to Male) Audio Cable | ||
| − | * Louroe Verifact A Microphone | + | * Louroe Verifact A Microphone |
| − | + | * T20 Torx security bit | |
| − | * | + | * Wire Stripper |
| − | * Wire Stripper | + | * Tap-Cons (if mounting to concrete) (3/16") |
| − | * | + | * Screws and Anchors (3/16") |
| − | * | ||
| − | |||
* Toggle Bolts (If mounting to drop ceiling tile) | * Toggle Bolts (If mounting to drop ceiling tile) | ||
| − | |||
* Drill bit and drill | * Drill bit and drill | ||
| − | |||
* Phillips head drill bit or Phillips head screwdriver | * Phillips head drill bit or Phillips head screwdriver | ||
| − | * Small Flat head screwdriver | + | * Small Flat head screwdriver (#3) |
| − | |||
* Cat5/6 Patch Cable (7ft-15ft recommended) | * Cat5/6 Patch Cable (7ft-15ft recommended) | ||
| − | * | + | * Stranded Shielded 22/2 + ground Wire |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | {{F41 F1005 Installation Instructions}} | |
| − | + | {{F41 VerifactA}} | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Latest revision as of 10:25, 18 May 2020
Contents
Wiring Diagram
Select Optional Second Camera
Axis P3235
Axis P3245
Axis P3364/P3365
Axis P3374/P3375
Axis Axis F41
Axis P5414/P5415
Axis Axis M5525
Axis Axis P5635
Axis P5655
Axis V5914/V5915
Axis Q8414
Required Parts And Tools
- Axis F41 Main Unit
- Axis F1005
- Axis F8001
- 3.5mm (Male to Male) Audio Cable
- Louroe Verifact A Microphone
- T20 Torx security bit
- Wire Stripper
- Tap-Cons (if mounting to concrete) (3/16")
- Screws and Anchors (3/16")
- Toggle Bolts (If mounting to drop ceiling tile)
- Drill bit and drill
- Phillips head drill bit or Phillips head screwdriver
- Small Flat head screwdriver (#3)
- Cat5/6 Patch Cable (7ft-15ft recommended)
- Stranded Shielded 22/2 + ground Wire
Installation Instructions
Mounting the Processing Unit
- Locate the network drop above the ceiling. It should be terminated with a male Ethernet end (service loop) or a biscuit jack. This line will have been ran back to the POE switch.
- Note: If the switch does not have POE, a POE injector will need to be installed at the network closet.
- Using the T20 bit, remove the rubber feet from the bottom of the Axis F41 Main Unit, and replace it with the Axis F8001. This will allow the F41 to be mounted to drywall above the drop ceiling.
-
- Find the a suitable mounting location for the F41. Using a pencil, mark the location the four anchors will be mounted
- Using a drill and drill bit, drill the mounting locations.
- Insert the four anchors and screws (or wall dogs), and mount the F41 into the drywall above the drop ceiling.
- Note: if there is no drop ceiling make other arrangements for mounting.
-
-
- Connect the network drop to the Axis F41 Main Unit. When connected, the NET, STATUS, and POWER LEDs will show green on the unit. After approximately one minute, all three indicators should be green.
-
Mounting the Camera
- Assemble the mounting unit for the Axis F1005.
- Mount the camera into the drop ceiling using toggle bolts.
- Run the attached RJ-11 cable to the input labeled CAM on the Axis F41 Main Unit. Ensure to drill an appropriate hole in the drop ceiling to feed the RJ-11 cable through.
Connecting the Microphone
- Mark center of the ceiling tile the Verifact A will be mounted on.
- Using a hole saw, drill a hole at center of the ceiling tile. Feed one end of the the 22/2 cables through the hole.
- Note: Ensure that the hole will be covered by the microphone
-
- Strip the jacket off the 22/2, revealing the red, black, and common (bare wire) on both sides of the cable.
- Remove the string and plastic casings covering the red and black cables.
- Strip the red and black jackets off the wire exposing the copper. Cut copper evenly on both ends. Remove ground.
- At the Verifact A, connect the power cable to ports A and C. Connect the audio cable to ports B and C.
-
- Using toggle bolts, secure the microphone.
-
- Connect the other ends of the 22/2 cable to the terminals on F41.
- The audio line will be connected to a 3.5mm audio cable (cut approx. 12") with B-connectors and inserted in the "Audio In" port
- Power will be connected to the I/O connector (Black to 1, Red to 2)
-
