Installing an Axis F41 and Axis F4005 sensor unit with a Louroe Verifact D Microphone

Required Parts And Tools

Axis F41 Main Unit
Axis F4005
Axis F8001
3.5mm (Male to Male) Audio Cable
Louroe Verifact D Microphone
T10 Torx security bit
Wire Stripper
Wall Dogs (if mounting to concrete) (3/16")
Screws and Anchors (3/16")
Toggle Bolts (If mounting to drop ceiling tile) (3/16")
Drill bit and drill
Phillips head drill bit or Phillips head screwdriver
Small Flat head screwdriver (#3)
Cat5/6 Patch Cable (7ft-15ft recommended)
Shielded Stranded 22/2 + ground Wire
1 Mud ring if mounting to drywall, Datacom box if mounting to hard surface (ex. Cinderblock)
Drywall Saw

Locate the network drop above the ceiling. It should be terminated with a male Ethernet end (service loop) or a biscuit jack. This line will have been ran back to the POE switch.
Note: If the switch does not have POE, a POE injector will need to be installed at the network closet.
Using the T10 bit, remove the rubber feet from the bottom of the Axis F41 Main Unit, and replace it with the Axis F8001. This will allow the F41 to be mounted to drywall above the drop ceiling.
Find the a suitable mounting location for the F41. Using a pencil, mark the location the four anchors will be mounted
Using a drill and drill bit, drill the mounting locations
Insert the four anchors and screws (or wall dogs), and mount the F41 into the drywall above the drop ceiling.
Note: if there is no drop ceiling make other arrangements for mounting.
Connect the network drop to the Axis F41 Main Unit. When connected, the NET, STATUS, and POWER LEDs will show green on the unit. After approximately one minute, all three indicators should be green.

Determine where on the drop ceiling tile the F4005 will be mounted
Using a paddle bit, drill a hole where the RJ-11 cable will pass through and be ran to the F41 main unit.
Using toggle bolts, mount the F4005 housing to the drop ceiling.
Note: If going for a more recessed look, mount the F4005 directly to the ceiling using toggle bolts.
Run the attached RJ-11 cable to the input labeled CAM on the Axis F41 Main Unit.
Secure the dome ring around the F4005

Using a pencil, mark the locations where the two anchors will be place.
Using a drill and drill bit, drill the holes and insert anchors
Using a paddle bit, drill a hole where the RJ-11 cable will pass through and be ran to the F41 main unit.
Mount the F4005 using screws
Run the attached RJ-11 cable to the input labeled CAM on the Axis F41 Main Unit.
Secure the dome ring around the F4005

Cut two lengths of 22/2. One will be for power. One will be for audio signal. Strip the jacket off the 22/2, revealing the red, black, and common (bare wire) on both sides of the cable. Remove the string and plastic casings covering the red and black cables. Strip the red and black jackets off the wire exposing the copper. Cut copper evenly on both ends (See picture).
Cut a hole into the drywall, large enough to fit the mud ring into it securely. Feed one end of the the 22/2 audio cable through the hole. (If mounting on a hard surface, attached Datacom box to the wall). If mounting to ceiling tile, mark center on the drop ceiling tile and trace the location of the mud ring. Using a dry wall saw, cut out the mud ring location. When securing the mud ring, be careful not to over tighten. Connect the audio cable to the Verifact-D phoenix terminal as follows; Red to A, Black to B, Common (bare wire) to C (See Picture)
Connect the other end of the 22/2 cables to the ports on the F41 unit. One will be connected to the 3.5mm cable with B-connectors for audio. The other will be connected to the I/O port for power (Red to 2, Black to 1)
Use the 3.5mm Male to Male audio cable and connect it into the “AUDIO IN” on the Axis F41 Main Unit. (cut approx. 12") (See Picture)
Align Verifact-D with mud ring or Datacom box and screw in securely.

Select Optional Second Camera

Axis P3235

Axis P3245

Axis P3364/P3365

Axis P3374/P3375

Axis Axis F41

Axis P5414/P5415

Axis Axis M5525

Axis Axis P5635

Axis P5655

Axis V5914/V5915

Axis Q8414