Difference between revisions of "Public Talkback - Overhead Speaker"
IVSWikiBlue (talk | contribs) (Created page with "==Required Parts And Tools== * Output Speaker (may be overhead or in wall mounted) * Shure MX393 Boundary Mic * RDL STM-1 Preamp * F-XLR Tail * RDL ST-VOX1 * 22/2 audio ca...") |
IVSWikiBlue (talk | contribs) (→Installation Instructions) |
||
| Line 20: | Line 20: | ||
#:'''Note:''' The wires of the XLR will wire to the +, -, and ground Input on the STM-1. | #:'''Note:''' The wires of the XLR will wire to the +, -, and ground Input on the STM-1. | ||
#Secure a pass through plate to the mud ring mounted for the XLR just ran | #Secure a pass through plate to the mud ring mounted for the XLR just ran | ||
| − | + | #Place the MX393. This mic line will connect the mic line to the STM-1 | |
| − | #Place the MX393. | ||
| − | |||
#Mount the STM-1 above the ceiling | #Mount the STM-1 above the ceiling | ||
#Wire the red to the + and black to the ground power terminals on the STM-1. | #Wire the red to the + and black to the ground power terminals on the STM-1. | ||
| Line 29: | Line 27: | ||
#Strip the jacket from the cable and remove all contents keeping only the red cable. | #Strip the jacket from the cable and remove all contents keeping only the red cable. | ||
#On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal. | #On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal. | ||
| − | #Run another length of 22/2 cable from the STM-1 to the | + | #Run another length of 22/2 cable from the STM-1 to the a ST-VOX1 |
| + | ===Wiring the ST-VOX1=== | ||
Revision as of 09:14, 14 April 2021
Contents
Required Parts And Tools
- Output Speaker (may be overhead or in wall mounted)
- Shure MX393 Boundary Mic
- RDL STM-1 Preamp
- F-XLR Tail
- RDL ST-VOX1
- 22/2 audio cable
- B-connectors
- Fish Tape or Glow Rods
- Electrical Tape
- Wire Stripper
Installation Instructions
Mounting the Audio
- Decide where the STM-1 will be located, knowing the MX393 mic will need to reach it.
- Using a stud finder, determine the best location to route the 22/2 cable
- Cut a hole into the drywall, large enough to fit a mud ring into it securely.
-
- Using glow rods or fish tape, pass the 22/2 behind the wall routing to the STM-1
- Note: The wires of the XLR will wire to the +, -, and ground Input on the STM-1.
- Secure a pass through plate to the mud ring mounted for the XLR just ran
- Place the MX393. This mic line will connect the mic line to the STM-1
- Mount the STM-1 above the ceiling
- Wire the red to the + and black to the ground power terminals on the STM-1.
- Cut a length of 22/2 from the STM-1 to the camera. Strip the jacket on both ends. Cut away the bare wire and plastic surround the cable inside. Strip away a small piece of the red and black jackets revealing the bare copper wire.
- A short piece of 22/2 cable will also be needed (approx. 1 inch).
- Strip the jacket from the cable and remove all contents keeping only the red cable.
- On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
- Run another length of 22/2 cable from the STM-1 to the a ST-VOX1
