Difference between revisions of "Push-to-talk Talk Back"

From IVS Wiki
Jump to: navigation, search
(→‎Required Parts And Tools)
 
(6 intermediate revisions by the same user not shown)
Line 12: Line 12:
  
 
==Installation Instructions==
 
==Installation Instructions==
−
#Once the camera is installed, locate the power out from the camera.
+
===Mounting the Audio===
 
#Decide where the STM-1 will be located, knowing the MX393 mic will need to reach it.  
 
#Decide where the STM-1 will be located, knowing the MX393 mic will need to reach it.  
−
#Place the MX393. Plug the mic into the F-XLR tail.
+
#Determine a suitable place to mount the RDL EZ-MCP1, ideally beneath the work station
−
#The wires of the XLR will wire to the +, -, and ground Input on the STM-1. (You may want to splice a short length of 22/2 to make it easier to wire to the STM-1 terminals.)
+
#Using a stud finder, determine the best location to route the 22/2 cable
 +
#Cut a hole into the drywall, large enough to fit a mud ring into it securely. 
 +
#: [[File:VerifactDring.JPG|link=https://ipivs.com/wiki/images/4/4d/VerifactDring.JPG|170px]]
 +
# Using glow rods or fish tape, pass the 22/2 behind the wall routing to the STM-1
 +
#:'''Note:''' The wires of the XLR will wire to the +, -, and ground Input on the STM-1.
 +
#Secure a pass through plate to the mud ring mounted for the XLR just ran
 +
#Using anchors and screws, mount the compressor
 +
#Place the MX393. Plug the mic into the F-XLR tail into input of the compressor. Plug the line to the STM-1 into the output of the compressor.
 +
#: [[File:UnderDeskMX393.jpeg|https://ipivs.com/wiki/images/5/5f/UnderDeskMX393.jpeg|500px]]
 +
#Mount the STM-1 above the ceiling
 +
#Wire the red to the + and black to the ground power terminals on the STM-1.
 
#Cut a length of 22/2 from the STM-1 to the camera. Strip the jacket on both ends. Cut away the bare wire and plastic surround the cable inside. Strip away a small piece of the red and black jackets revealing the bare copper wire.
 
#Cut a length of 22/2 from the STM-1 to the camera. Strip the jacket on both ends. Cut away the bare wire and plastic surround the cable inside. Strip away a small piece of the red and black jackets revealing the bare copper wire.
−
#Wire one end to the power out on your camera.
+
#A short piece of 22/2 cable will also be needed (approx. 1 inch).  
−
#On the other end, wire the red to the + and black to the ground power terminals on the STM-1.
+
#Strip the jacket from the cable and remove all contents keeping only the red cable.
−
#You will also need to cut a short piece of 22/2 cable (approx. 1 inch).  
+
#On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.  
−
#Strip the jacket from the cable and remove all contents keeping only the red cable. On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.  
+
#Run another length of 22/2 cable from the STM-1 to the audio connectors on the back of the speaker.
−
#Run another length of 22/2 cable from the STM-1 to the IR T1. Wire red to +, black to -, and bare to ground terminals on the Lo-Z Output on the STM-1.
 
−
#:''Note:'' If the customer desires to capture the audio from this talkback mic, you will need to wire up another run of 22/2 cable connecting to a mixer that eventually feeds the camera audio.
 
−
#Expose the wires on the other end by the IR. Cut a 3.5mm cable open, test for continuity, then splice it with the 22/2 with B-connectors. Cover your splice with electrical tape.
 
−
#Plug the 3.5 cable into the Line In of the IR T1.
 
−
#Once audio is plugged in, locate your nearest power outlet to power the IR T1.
 
−
#:''Note:'' You may need to use 18/2 cable to add length to the power cable. Ensure that when splicing in the 18/2 to the power, that the red jacket of the 18/2 is spliced into the cable with the dashed white lines on the power supply.
 
−
#Ensure your IR T1 and RX224 are set to the same channel.
 
−
#Test the talkback unit is working by activating the talkback function within the VALT Software and having a partner to communicate with.
 
−
[[File:Talkback Turn On.jpg|720x960px|link=https://ipivs.com/wiki/images/9/90/Talkback_Turn_On.jpg]]
 

Latest revision as of 09:31, 13 April 2021

Required Parts And Tools

  • Williams Talkback System IR T1
  • Williams RX224 Receiver
  • Shure MX393 Boundary Mic
  • RDL STM-1 Preamp
  • F-XLR Tail
  • 22/2 audio cable
  • B-connectors
  • Fish Tape or Glow Rods
  • Electrical Tape
  • Wire Stripper

Installation Instructions

Mounting the Audio

  1. Decide where the STM-1 will be located, knowing the MX393 mic will need to reach it.
  2. Determine a suitable place to mount the RDL EZ-MCP1, ideally beneath the work station
  3. Using a stud finder, determine the best location to route the 22/2 cable
  4. Cut a hole into the drywall, large enough to fit a mud ring into it securely.
    VerifactDring.JPG
  5. Using glow rods or fish tape, pass the 22/2 behind the wall routing to the STM-1
    Note: The wires of the XLR will wire to the +, -, and ground Input on the STM-1.
  6. Secure a pass through plate to the mud ring mounted for the XLR just ran
  7. Using anchors and screws, mount the compressor
  8. Place the MX393. Plug the mic into the F-XLR tail into input of the compressor. Plug the line to the STM-1 into the output of the compressor.
    https://ipivs.com/wiki/images/5/5f/UnderDeskMX393.jpeg
  9. Mount the STM-1 above the ceiling
  10. Wire the red to the + and black to the ground power terminals on the STM-1.
  11. Cut a length of 22/2 from the STM-1 to the camera. Strip the jacket on both ends. Cut away the bare wire and plastic surround the cable inside. Strip away a small piece of the red and black jackets revealing the bare copper wire.
  12. A short piece of 22/2 cable will also be needed (approx. 1 inch).
  13. Strip the jacket from the cable and remove all contents keeping only the red cable.
  14. On both ends of the red cable, strip off a piece of the jacket. Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
  15. Run another length of 22/2 cable from the STM-1 to the audio connectors on the back of the speaker.
Retrieved from "https://ipivs.info/wiki/index.php?title=Push-to-talk_Talk_Back&oldid=8110"