Installing an Axis F41 and Axis F1005 sensor unit with a Louroe Verifact D Microphone

Wiring Diagram

Select Optional Second Camera

Axis P3235

Axis P3245

Axis P3364/P3365

Axis P3374/P3375

Axis Axis F41

Axis P5414/P5415

Axis Axis M5525

Axis Axis P5635

Axis P5655

Axis V5914/V5915

Axis Q8414

Axis F41 Main Unit
Axis F1005
Axis F8001
3.5mm (Male to Male) Audio Cable
Louroe Verifact D Microphone
T10 Torx security bit
Wire Stripper
Tap-Cons (if mounting to concrete) (3/16")
Screws and Anchors (3/16")
Toggle Bolts (If mounting to drop ceiling tile) (3/16")
Drill bit and drill
Phillips head drill bit or Phillips head screwdriver
Small Flat head screwdriver (#3)
Cat5/6 Patch Cable (7ft-15ft recommended)
Shielded Stranded 22/2 + ground Wire
1 Mud ring if mounting to drywall or drop ceiling, Datacom box if mounting to hard surface (ex. Cinderblock)
Drywall Saw

Locate the network drop above the ceiling. It should be terminated with a male Ethernet end (service loop) or a biscuit jack. This line will have been ran back to the POE switch.
Note: If the switch does not have POE, a POE injector will need to be installed at the network closet.
Using the T20 bit, remove the rubber feet from the bottom of the Axis F41 Main Unit, and replace it with the Axis F8001. This will allow the F41 to be mounted to drywall above the drop ceiling.
Find the a suitable mounting location for the F41. Using a pencil, mark the location the four anchors will be mounted
Using a drill and drill bit, drill the mounting locations.
Insert the four anchors and screws (or wall dogs), and mount the F41 into the drywall above the drop ceiling.
Note: if there is no drop ceiling make other arrangements for mounting.
Connect the network drop to the Axis F41 Main Unit. When connected, the NET, STATUS, and POWER LEDs will show green on the unit. After approximately one minute, all three indicators should be green.

Assemble the mounting unit for the Axis F1005.
Mount the camera into the drop ceiling using toggle bolts.
Run the attached RJ-11 cable to the input labeled CAM on the Axis F41 Main Unit. Ensure to drill an appropriate hole in the drop ceiling to feed the RJ-11 cable through.

Using a stud finder, scan the mounting location of the Verifact D ensure the microphone is not mounted on a stud.
Cut a hole into the drywall, large enough to fit the mud ring into it securely.
Using the hole saw, drill a hole above the drop ceiling in line with the hole drilled where the Verifact D is mounted.
Feed one end of the the 22/2 audio cables through the hole. (If mounting on a hard surface, attached Datacom box to the wall).
Strip the jacket off the 22/2, revealing the red, black, and common (bare wire) on both sides of the cable.
Remove the string and plastic casings covering the red and black cables. Strip the red and black jackets off the wire exposing the copper. Cut copper evenly on both ends (See picture)
Connect the 22/2 cables to the Verifact-D phoenix terminal as follows; Audio - Red to B, Black to C, Power - Red to A, Black to C (See Picture).
Align Verifact-D with mud ring or Datacom box and screw in securely.
Connect the other ends of the 22/2 cable to the terminals on F41.

The audio line will be connected to a 3.5mm audio cable (cut approx. 12") with B-connectors and inserted in the "Audio In" port
Power will be connected to the I/O connector (Black to 1, Red to 2)