Installing an Axis F41 and Axis F1005 sensor unit with a Shure MX202i Microphone

Wiring Diagram

Select Optional Second Camera

Axis P3235

Axis P3245

Axis P3364/P3365

Axis P3374/P3375

Axis Axis F41

Axis P5414/P5415

Axis Axis M5525

Axis Axis P5635

Axis P5655

Axis V5914/V5915

Axis Q8414

Locate the network drop above the ceiling. It should be terminated with a male Ethernet end (service loop) or a biscuit jack. This line will have been ran back to the POE switch.
Note: If the switch does not have POE, a POE injector will need to be installed at the network closet.
Using the T20 bit, remove the rubber feet from the bottom of the Axis F41 Main Unit, and replace it with the Axis F8001. This will allow the F41 to be mounted to drywall above the drop ceiling.
Find the a suitable mounting location for the F41. Using a pencil, mark the location the four anchors will be mounted
Using a drill and drill bit, drill the mounting locations.
Insert the four anchors and screws (or wall dogs), and mount the F41 into the drywall above the drop ceiling.
Note: if there is no drop ceiling make other arrangements for mounting.
Connect the network drop to the Axis F41 Main Unit. When connected, the NET, STATUS, and POWER LEDs will show green on the unit. After approximately one minute, all three indicators should be green.

Assemble the mounting unit for the Axis F1005.
Mount the camera into the drop ceiling using toggle bolts.
Run the attached RJ-11 cable to the input labeled CAM on the Axis F41 Main Unit. Ensure to drill an appropriate hole in the drop ceiling to feed the RJ-11 cable through.

Cut a short piece of 22/2 cable (approx. 1 inch). Strip the jacket and from the cable and remove all contents keeping only the red cable. On both ends of the red cable, strip off a piece of the jacket (See picture).
Connect one end of the 1 inch audio cable to the +PWR terminal and connect the other end into the +PHNTM terminal.
Connect the cable ran for power to both PWR terminals (Red to +, Black to the other terminal) of the STM-1. Connect the other side to the IO phoenix connector (Red to 2, Black to 1).
Connect the cable ran for audio to both LO-Z OUTPUT terminals (Red to +, Black to -, and ground to the ground terminal) of the STM-1. Connect the other end of the 3.5mm cable to the in on the F41. (cut to appropriate length between STM-1 and F41)

Asses the drop ceiling to decide best mounting placement for the MX202i. Avoid tiles adjacent to HVAC or fire safety devices.
Drill a hole into the center of the single gang plate using the ½” paddle bit (if not prefabricated).
Measure center of the drop ceiling tile and drill a similar hole with the ½” paddle bit.
Align the single gang plate to the location of the microphone on the drop ceiling tile using a pair of toggle bolts.
Run the MX202i through the ½” hole in the ceiling tile and single gang plate with the rubber stopper to secure the microphone in place and plugging the ½” hole .
Adjust the length of the cable of the microphone to a desirable length, hiding the remainder in the ceiling near the STM-1. Attach the windscreen to the MX202i.
Run the XLR mini cable to the STM-1 location.
Connect the connect the XLR mini to the 4 pin Male XLR adapter.
Strip away a portion of the red and black cables inside the pigtail, revealing the copper wire inside.
- The microphone will be connected via the input terminals of the STM-1 (Red to +, Black to -, ground to the ground terminal).
Connect the female XLR to the Male XLR adapter
Connect the other ends of the 22/2 cable to the terminals on F41.

The audio line will be connected to a 3.5mm audio cable (cut approx. 12") with B-connectors and inserted in the "Audio In" port
Power will be connected to the I/O connector (Black to 1, Red to 2)