Installing an Axis P3235 with a Louroe Verifact D Microphone

Wiring Diagram

Select Optional Second Camera

Axis P3235

Axis P3245

Axis P3364/P3365

Axis P3374/P3375

Axis Axis F41

Axis P5414/P5415

Axis Axis M5525

Axis Axis P5635

Axis P5655

Axis V5914/V5915

Axis Q8414

Required Parts and Tools

• Axis P3235
• 3.5mm (Male to Male) Audio Cable
• Louroe Verifact A Microphone
• T20 Torx security bit
• Wire Stripper
• Tapcons (if mounting to concrete) (3/16")
• Screws and Anchors (3/16")
• Toggle bolts (If mounting to drop ceiling tile) (3/16")
• 1/2" paddle bit
• 3.5mm Audio Cable
• Toggle Bolts (for mic mount)
• Drill bit and drill
• Phillips head drill bit or Phillips head screwdriver
• Small Flat head screwdriver (#3)
• Hole Saw
• B Connectors
• Stud Finder
• Cat5/6 Patch Cable (7ft-15ft recommended)
• Shielded Stranded 22/2 + ground Wire
• Fish Tape or Glow Rods

Installation Instructions

Disassemble the Camera

1. Locate the network drop above the ceiling. It should be terminated with a male Ethernet end (service loop) or a biscuit jack. This line will have been ran back to the POE switch.

   Note: If the switch does not have POE, a POE injector will need to be installed at the network closet.

2. Using the T20 bit, remove the dome from the 3235.
3. Remove protective foam and remove the camera from the mounting plate.

Drywall Mounting Instructions

1. Using a stud finder, scan the mount location to ensure the camera is not mounted on a stud.
2. Using a pencil, mark the four holes for the mount plate.
3. Using a 3/16" drill bit, drill the marked locations and
4. Install anchors and attach the mount plate using screws and washers.

   

5. Using a hole saw or paddle bit, cut a hole centered in the wall plate where cables will pass through.

   

6. Using the hole saw, drill a hole above the drop ceiling in line with the hole drilled where the camera is mounted.
7. Cut two lengths of 22/2 long enough to reach the mounting location of the microphone.
8. Using glow rods or fish tape, fish the network drop or patch cable in addition to the two sections of 22/2 audio cable through the drywall.
9. Attach the camera the the mount plate

Drop Ceiling Mounting Instructions

1. If mounting to drop ceiling, determine where the camera will be located on the tile. Ensure that there will be clearance on the tile to secure the dome in place.
2. Using two toggle bolts, secure the mount plate.

   

3. Using a 1" paddle bit, drill a hole centered in the opening of wall plate. This is where cables will pass through.

   

4. Cut two lengths of 22/2 long enough to reach the mounting location of the microphone.
5. Using glow rods or fish tape, fish the network drop and 2 sections of 22/2 audio cable into the drop ceiling.
6. Attach camera to mount plate.

Note: Be careful not to press too hard and damage the ceiling tile

Connect Wiring

1. Connect patch cable into the Ethernet port on the Axis P3235.

   Note: When connected, activity will be visible on the link lights. If no link lights appear, ensure that POE is enabled on the POE switch and that the network drop is plugged in. After approximately one minute, all three LEDs should be green.

2. At the camera, connect the power cable to the I/O phoenix connector (Red to 2, Black to 1). Connect the audio cable to the audio terminal block (Red to 3, Black to 1)

   

Aim the Camera

1. In order to aim the camera, it will need to be accessed via the Axis web portal.
2. If the camera is being powered off the network, run Axis IP utility in order to discover the camera. Clicking the IP address will route to the Axis web portal

   

3. If that does not work then use a POE injector to connect to the camera and the default IP. (default Axis IP = 192.168.0.90)
4. Using a laptop/PC, enter the IP address assigned to the camera into a web browser.

   

5. Using the IVS admin credentials, log into the camera.

   User: root

   Password: admin51

6. Once in the Axis web portal, activate the camera live view.

   

7. Begin by manually adjusting camera's viewing area using the manual tilt and focus mechanisms on the camera.

   

8. Using the digital zoom function in the web portal, make any other adjustments needed.
9. The image field may also be rotated in the web portal if necessary.

   

10. Be sure to click the Autofocus button. This will focus the camera and ensure that the autofocus is properly functioning.

    

    Note: This must be done before securing the dome.

Reassemble the Camera

1. Place the dome over on the camera. Using the T20 bit, tighten the dome cover in place.

   Note: Be sure when tightening the dome to not cause the camera to move.

2. Remove protective plastic from the camera dome

Connecting the Microphone

1. Using a stud finder, scan the mounting location of the Verifact D ensure the microphone is not mounted on a stud.
2. Cut a hole into the drywall, large enough to fit the mud ring into it securely.

   

3. Using the hole saw, drill a hole above the drop ceiling in line with the hole drilled where the Verifact D is mounted.
4. Feed one end of the the 22/2 audio cables through the hole. (If mounting on a hard surface, attached Datacom box to the wall).
5. Strip the jacket off the 22/2, revealing the red, black, and common (bare wire) on both sides of the cable.
6. Remove the string and plastic casings covering the red and black cables. Strip the red and black jackets off the wire exposing the copper. Cut copper evenly on both ends (See picture)

   

7. Connect the 22/2 cables to the Verifact-D phoenix terminal as follows; Audio - Red to B, Black to C, Power - Red to A, Black to C (See Picture).

   

8. Align Verifact-D with mud ring or Datacom box and screw in securely.