Installing an Axis P5655-E with a Louroe Verifact A

Wiring Diagram

Select Optional Second Camera

Axis P3235

Axis P3245

Axis P3364/P3365

Axis P3374/P3375

Axis Axis F41

Axis P5414/P5415

Axis Axis M5525

Axis Axis P5635

Axis P5655

Axis V5914/V5915

Axis Q8414

Required Parts And Tools

• Axis P5655
• AXIS T94A02L Recessed Mount (If mounting to drop ceiling)
• 3.5mm (Male to Male) Audio Cable
• Louroe Verifact A Microphone
• Axis MultiCable C I/O Audio & Power
• Axis Push-Pull connector
• T20 security bit
• Wire Stripper
• Tap-Cons (if mounting to concrete) (3/16")
• Screws and Anchors (3/16")
• Toggle Bolts (If mounting to drop ceiling tile) (3/16")
• Drill bit and drill
• Phillips head drill bit or Phillips head screwdriver
• Small Flat head screwdriver (#3)
• Shielded Stranded 22/2 + ground Wire
• Razor / box cutter
• B-Connectors

Installation Instructions

Mounting the Camera

1. Locate the network drop above the ceiling either being a male Ethernet end (service loop) or a biscuit jack. This will have been ran back to the POE switch.

   Note: If the switch does not have POE, a POE injector will need to be installed at the network closet.

2. Remove Axis T94A02L kit from packaging. This will include the mounting bracket and the camera dome ring.
3. Determine the location where the 5655 will be mounted and remove the ceiling tile
4. Measuring the ceiling mount bracket, note that there is a slight lip to the camera mount

   

5. Find center of the ceiling tile and using a pencil, draw a circle approximately nine inches in diameter
6. Using a drywall saw, cut out the section of ceiling tile where the mount will be inserted

   

7. Using a T20 bit, tighten the mounting arms of the ceiling mount

   

   Note: Ensure not to over tighten into the ceiling tile.

8. Pass the Axis MultiCable C I/O and the Ethernet cable through the hole at the top of the camera mount

   

9. Connect cables to their respective ports

   

10. Before locking the 5635 to the mounting posts in the ceiling mount, ensure that the safety cable is attached to the camera

    

11. Insert the camera into the ceiling mount and twist until locked in place securely

    

12. Using a T20 bit, secure the dome ring to the camera mount

    

13. Carefully return the ceiling tile to its location

Note: If not using drop ceiling, use alternate instructions inside of the box for mounting to a hard ceiling.

Connecting Wiring

1. Begin but cutting two lengths of 22/2. Ensure they are long enough to reach the microphone location. One will be for audio signal. One will be for power.
2. Strip the jacket off the 22/2, revealing the red, black, and common (bare wire) on both sides of the cable.
3. Remove the string and plastic casings covering the red and black cables.
4. Strip the red and black jackets off the wire exposing the copper. Cut copper evenly on both ends. Remove ground.
5. At the Axis MultiCable C I/O, connect the ends of 22/2
   • Audio will be connected to the "In" on the audio terminal block - Red to +, Black to -
   • Power will be connected to the I/O terminal block - Red to to 2, Black to 1

   

Connecting the Microphone

1. Mark center of the ceiling tile the Verifact A will be mounted on.
2. Using a hole saw, drill a hole at center of the ceiling tile. Feed one end of the the 22/2 cables through the hole.

   Note: Ensure that the hole will be covered by the microphone

   

3. Strip the jacket off the 22/2, revealing the red, black, and common (bare wire) on both sides of the cable.
4. Remove the string and plastic casings covering the red and black cables.
5. Strip the red and black jackets off the wire exposing the copper. Cut copper evenly on both ends. Remove ground.
6. At the Verifact A, connect the power cable to ports A and C. Connect the audio cable to ports B and C.

   

7. Using toggle bolts, secure the microphone.