Difference between revisions of "Unboxing Your VALT POC System"

From IVS Wiki
Jump to: navigation, search
 
(5 intermediate revisions by the same user not shown)
Line 1: Line 1:
The VALT POC system will be shipped to you in a weather proof hard case. Everything required for you Valt Proof of Concept demonstration will be included in this case.
+
<div class="floating_card">The VALT POC system will be shipped to you in a weather proof hard case. Everything required for you VALT Proof of Concept demonstration will be included in this case.</div>
  
 +
<div class="section">
 
IVS will only ship the requested equipment for a POC. It may include the following:
 
IVS will only ship the requested equipment for a POC. It may include the following:
  
Line 6: Line 7:
 
* VALT POC Camera and Stand
 
* VALT POC Camera and Stand
 
* VALT POC Wireless Access Point
 
* VALT POC Wireless Access Point
 +
</div>
  
[[File:POC6.jpg|800x600px]]
+
{{img | file = PoCunbox1.jpg | width=400px}} {{img | file = POCunbox2.jpg | width=400px}}
  
 +
<div class="section">
 
The case will be locked with combination locks. Please contact your VALT Sales Representative for the combination.
 
The case will be locked with combination locks. Please contact your VALT Sales Representative for the combination.
  
 
Inside the case, you will find customized foam padding divided into layers. Please make sure to save all padding to use in the return shipment after the proof of concept is complete.
 
Inside the case, you will find customized foam padding divided into layers. Please make sure to save all padding to use in the return shipment after the proof of concept is complete.
  
The top layer will contain the VALT POC Appliance (if included), as well as any power cords.
+
On the top layer will be the back plate VALT POC Camera and Stand
  
[[File:POC7.jpg|800x600px]]
+
{{img | file = POCunbox3.jpg | width=600px}}
  
Remove the VALT POC Appliance and set it aside, then remove the top layer of foam.
+
Remove the VALT POC Cameras (back board) and set them aside.  
  
The second layer is just padding.
+
The next element will be the VALT POC Camera base. This houses all wiring, processing, and also contains the accessory panel
  
[[File:POC8.jpg|800x600px]]
+
{{img | file = POCunbox4.jpg | width=600px}}
  
Remove the second layer of foam.
+
Determine an appropriate location for the VALT POC Camera Station
  
The third layer contains the base for the VALT POC Camera and Stand.
+
{{img | file = PoCunbox6.jpg | width=600px}}
  
[[File:POC9.jpg|800x600px]]
+
Slide the VALT POC Camera (back board) into the opening into the base of the Stand. The back board should fit snugly.  
  
Remove the third layer of foam. There is a small piece of foam between the camera and the stand base.
+
{{img | file = POCpowered.jpg | width=600px}}
  
[[File:POC10.jpg|800x600px]]
+
On the back of the VALT POC Camera station, connect the wiring from the cameras to the input panel on the base
  
Remove the VALT POC Camera and Stand base, then remove the fourth layer of foam.
+
{{img | file = PoCunbox8.jpg | width=600px}} {{img | file = PoCunbox9.jpg | width=450px}}
 
+
</div>
The fifth layer contains the VALT POC Camera and Stand.
 
 
 
[[File:POC11.jpg|800x600px]]
 
 
 
Remove the Camera and Stand from the shipping container, and then place all the foam back in the container.
 
 
 
[[File:POC12.jpg|800x600px]]
 
 
 
Slide the VALT POC Camera and Stand into the base. The back plane should fit snugly between the two orange braces.
 
 
 
[[File:POC13.png|800x600px]]
 
 
 
The camera should hang over the open area of the base.
 
 
 
[[File:POC4.png|800x600px]]
 
 
 
Make sure to line up the brackets on the back plane with the slide locks on the base.
 
 
 
[[File:POC14.jpg|800x600px]]
 
 
 
Lock the back plane into place by sliding the the bolts from the base, into the brackets on the back plane.
 
 
 
[[File:POC15.jpg|800x600px]]
 
 
 
Connect the female XLR tail to the male XLR connector on the back of the microphone.
 
 
 
[[File:POC17.jpg|800x600px]]
 

Latest revision as of 16:56, 2 December 2022

The VALT POC system will be shipped to you in a weather proof hard case. Everything required for you VALT Proof of Concept demonstration will be included in this case.

IVS will only ship the requested equipment for a POC. It may include the following:

  • VALT POC Appliance
  • VALT POC Camera and Stand
  • VALT POC Wireless Access Point

PoCunbox1.jpg POCunbox2.jpg

The case will be locked with combination locks. Please contact your VALT Sales Representative for the combination.

Inside the case, you will find customized foam padding divided into layers. Please make sure to save all padding to use in the return shipment after the proof of concept is complete.

On the top layer will be the back plate VALT POC Camera and Stand

POCunbox3.jpg

Remove the VALT POC Cameras (back board) and set them aside.

The next element will be the VALT POC Camera base. This houses all wiring, processing, and also contains the accessory panel

POCunbox4.jpg

Determine an appropriate location for the VALT POC Camera Station

PoCunbox6.jpg

Slide the VALT POC Camera (back board) into the opening into the base of the Stand. The back board should fit snugly.

POCpowered.jpg

On the back of the VALT POC Camera station, connect the wiring from the cameras to the input panel on the base

PoCunbox8.jpg PoCunbox9.jpg