Difference between revisions of "OWI Overhead Speaker Installation Instructions"
IVSWikiBlue (talk | contribs) (Created page with "==Required Parts And Tools== * OWI Amplified Overhead Speaker * 3.5mm audio cable * 18/2 low voltage cable * B Connectors * Wire Stripper * 22/2 audio cable * Fish Tape...") |
IVSWikiBlue (talk | contribs) (→Installation Instructions) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
* OWI Amplified Overhead Speaker | * OWI Amplified Overhead Speaker | ||
* 3.5mm audio cable | * 3.5mm audio cable | ||
| + | * 22/2 shielded audio cable | ||
* 18/2 low voltage cable | * 18/2 low voltage cable | ||
| + | * Drywall saw | ||
* B Connectors | * B Connectors | ||
* Wire Stripper | * Wire Stripper | ||
| Line 8: | Line 10: | ||
* Fish Tape or Glow Rods | * Fish Tape or Glow Rods | ||
* Electrical Tape | * Electrical Tape | ||
| + | |||
| + | ==Installation Instructions== | ||
| + | ===Mounting Instructions=== | ||
| + | #Determine the most optimal placement for the OWI speaker | ||
| + | #:''Note:'' Avoid mounting adjacent to microphones to prevent signal looping | ||
| + | #Remove the ceiling tile to which the speaker will be mounted | ||
| + | #When removing the speaker from its packaging, note that there is a cutting template for the speaker. Ensure to remove the excess along the dashed line | ||
| + | #Using the cutting template, trace the template centered in the ceiling tile | ||
| + | #:[[File:OWItrace.JPG|link=https://ipivs.com/wiki/images/3/31/OWItrace.JPG]] | ||
| + | #Using a drywall saw, carefully cut out the mounting location | ||
| + | #:[[File:OWIcutHole.JPG|link=https://ipivs.com/wiki/images/5/59/OWIcutHole.JPG]] | ||
| + | #Flip the ceiling tile over and align the tile mounting plate with the cut hole. | ||
| + | #:[[File:OWImountPlate.JPG|link=https://ipivs.com/wiki/images/1/19/OWImountPlate.JPG]] | ||
| + | #Using a small tool, carefully remove the screen from the speaker. This is necessary in order to secure the mounting arms. | ||
| + | #:[[File:OWInoScreen.JPG|link=https://ipivs.com/wiki/images/a/aa/OWInoScreen.JPG]] | ||
| + | #With one hand on the speaker, insert the speaker into the mounting location and tighten the mounting arms securely to the mounting plate | ||
| + | #*''Note:'' It is easiest to get one arm nearly secured and adjust the mount plate before securing all four arms. | ||
| + | #:[[File:OWIarmsMount.JPG|link=https://ipivs.com/wiki/images/7/79/OWIarmsMount.JPG]][[File:OWIarmClamp.JPG|link=https://ipivs.com/wiki/images/5/53/OWIarmClamp.JPG]] | ||
| + | #Tap out the appropriate hole on the back of the speaker housing | ||
| + | #:[[File:OWIpunchOut.JPG|link=https://ipivs.com/wiki/images/f/fc/OWIpunchOut.JPG]] | ||
| + | #Connect the wiring before securing the speaker housing using the provided screws. | ||
| + | #*Audio will be connected from 22/2 ran from the camera and spliced with B-connectors to a 3.5mm audio cable. Insert in the 3.5mm In port (shown below). Ensure the gain control is not set at zero both on the 3.5mm and the master level. | ||
| + | #*Power will be connected to the phoenix terminal (shown below). Red to +, Black to - | ||
| + | #:[[File:OWIconnections.JPG|link=https://ipivs.com/wiki/images/8/86/OWIconnections.JPG]] [[File:OWIspkrCan.JPG|link=https://ipivs.com/wiki/images/6/6f/OWIspkrCan.JPG]] | ||
| + | ===Connecting to Power=== | ||
| + | #Determine if power is available above the ceiling or at outlet height. | ||
| + | #If running power to an outlet, determine the best location and route for running 18/2. | ||
| + | #Using a stud finder, scan the wall as near as possible to the power outlet, ensuring to not mount on a stud and remaining level with the power outlet. | ||
| + | #Cut a hole into the drywall, large enough to fit the mud ring into it securely. | ||
| + | #Using fish tape and glow rods, fish the 18/2 through the drywall. | ||
| + | #Once the 18/2 is through the cut hole, insert the mud ring and secure the cable pass through plate | ||
| + | #:[[File:PassThrough.JPG|200px|link=https://ipivs.com/wiki/images/9/91/PassThrough.JPG]] | ||
| + | #Strip back the shield of the 18/2 and the black and red wires. | ||
| + | #Using B-connectors, splice the power brick to the 18/2 | ||
| + | #Plug in the power block. A small pop may be heard from the speaker upon receiving power. | ||
| + | |||
| + | ===Connecting the Camera=== | ||
| + | #Once your camera is installed, locate the AUDIO OUT on your camera. | ||
| + | #Strip the jacket of the 22/2 cable revealing the red, black, and bare wires inside. | ||
| + | #Cut away the plastic surrounding the cable inside. Strip away a small piece of the red and black jackets revealing the bare copper wire. | ||
| + | #Wire the black and bare to the - and the red to the + of the AUDIO OUT of the phoenix connector. | ||
| + | #Run the 22/2 cable from the camera to the AMP2SIC5, wiring your red wire to the + phoenix connection and black to the - connection of the LINE INPUT of the AMP2SIC5 | ||
| + | #Run the 18/2 from the AMP2SIC5 to its designated power outlet. | ||
Latest revision as of 12:49, 12 May 2020
Contents
Required Parts And Tools
- OWI Amplified Overhead Speaker
- 3.5mm audio cable
- 22/2 shielded audio cable
- 18/2 low voltage cable
- Drywall saw
- B Connectors
- Wire Stripper
- 22/2 audio cable
- Fish Tape or Glow Rods
- Electrical Tape
Installation Instructions
Mounting Instructions
- Determine the most optimal placement for the OWI speaker
- Note: Avoid mounting adjacent to microphones to prevent signal looping
- Remove the ceiling tile to which the speaker will be mounted
- When removing the speaker from its packaging, note that there is a cutting template for the speaker. Ensure to remove the excess along the dashed line
- Using the cutting template, trace the template centered in the ceiling tile
- Using a drywall saw, carefully cut out the mounting location
- Flip the ceiling tile over and align the tile mounting plate with the cut hole.
- Using a small tool, carefully remove the screen from the speaker. This is necessary in order to secure the mounting arms.
- With one hand on the speaker, insert the speaker into the mounting location and tighten the mounting arms securely to the mounting plate
- Note: It is easiest to get one arm nearly secured and adjust the mount plate before securing all four arms.
- Tap out the appropriate hole on the back of the speaker housing
- Connect the wiring before securing the speaker housing using the provided screws.
- Audio will be connected from 22/2 ran from the camera and spliced with B-connectors to a 3.5mm audio cable. Insert in the 3.5mm In port (shown below). Ensure the gain control is not set at zero both on the 3.5mm and the master level.
- Power will be connected to the phoenix terminal (shown below). Red to +, Black to -
Connecting to Power
- Determine if power is available above the ceiling or at outlet height.
- If running power to an outlet, determine the best location and route for running 18/2.
- Using a stud finder, scan the wall as near as possible to the power outlet, ensuring to not mount on a stud and remaining level with the power outlet.
- Cut a hole into the drywall, large enough to fit the mud ring into it securely.
- Using fish tape and glow rods, fish the 18/2 through the drywall.
- Once the 18/2 is through the cut hole, insert the mud ring and secure the cable pass through plate
- Strip back the shield of the 18/2 and the black and red wires.
- Using B-connectors, splice the power brick to the 18/2
- Plug in the power block. A small pop may be heard from the speaker upon receiving power.
Connecting the Camera
- Once your camera is installed, locate the AUDIO OUT on your camera.
- Strip the jacket of the 22/2 cable revealing the red, black, and bare wires inside.
- Cut away the plastic surrounding the cable inside. Strip away a small piece of the red and black jackets revealing the bare copper wire.
- Wire the black and bare to the - and the red to the + of the AUDIO OUT of the phoenix connector.
- Run the 22/2 cable from the camera to the AMP2SIC5, wiring your red wire to the + phoenix connection and black to the - connection of the LINE INPUT of the AMP2SIC5
- Run the 18/2 from the AMP2SIC5 to its designated power outlet.
