Difference between revisions of "Template:P3245LV Mount The Camera"
IVSWikiBlue (talk | contribs) (→Drywall mounting instructions) |
IVSWikiBlue (talk | contribs) (→Mount the Camera) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 5: | Line 5: | ||
#Using a 3/16" drill bit, drill the marked locations and | #Using a 3/16" drill bit, drill the marked locations and | ||
#Install anchors and attach the mount plate using screws and washers. | #Install anchors and attach the mount plate using screws and washers. | ||
| − | #: | + | #:{{img | file = 3245Drywall2.JPG | width=170px}} |
#Using a hole saw or paddle bit, cut a hole centered in the wall plate where cables will pass through. | #Using a hole saw or paddle bit, cut a hole centered in the wall plate where cables will pass through. | ||
| − | #: | + | #:{{img | file = 3245DrywallHole2.JPG | width=170px}} |
#Using the hole saw, drill a hole above the drop ceiling in line with the hole drilled where the camera is mounted. | #Using the hole saw, drill a hole above the drop ceiling in line with the hole drilled where the camera is mounted. | ||
#Cut two lengths of 22/2 long enough to reach the mounting location of the microphone. | #Cut two lengths of 22/2 long enough to reach the mounting location of the microphone. | ||
#Using glow rods or fish tape, fish the network drop or patch cable in addition to the two sections of 22/2 audio cable through the drywall. | #Using glow rods or fish tape, fish the network drop or patch cable in addition to the two sections of 22/2 audio cable through the drywall. | ||
#Attach the camera the the mount plate | #Attach the camera the the mount plate | ||
| − | #: | + | #:{{img | file = 3245DrywalPlate2.JPG | width=170px}} |
====Drop Ceiling mount instructions==== | ====Drop Ceiling mount instructions==== | ||
#If mounting to drop ceiling, determine where the camera will be located on the tile. Ensure that there will be clearance on the tile to secure the dome in place. | #If mounting to drop ceiling, determine where the camera will be located on the tile. Ensure that there will be clearance on the tile to secure the dome in place. | ||
#Using two toggle bolts, secure the mount plate. | #Using two toggle bolts, secure the mount plate. | ||
| − | #: | + | #:{{img | file = 3245dropC2.JPG | width=170px}} |
#Using a 1" paddle bit, drill a hole centered in the opening of wall plate. This is where cables will pass through. | #Using a 1" paddle bit, drill a hole centered in the opening of wall plate. This is where cables will pass through. | ||
| − | #: | + | #:{{img | file = 3245dropCHole2.JPG | width=170px}} |
#Cut two lengths of 22/2 long enough to reach the mounting location of the microphone. | #Cut two lengths of 22/2 long enough to reach the mounting location of the microphone. | ||
#Using glow rods or fish tape, fish the network drop and 2 sections of 22/2 audio cable into the drop ceiling. | #Using glow rods or fish tape, fish the network drop and 2 sections of 22/2 audio cable into the drop ceiling. | ||
#Attach camera to mount plate. | #Attach camera to mount plate. | ||
| − | #: | + | #: {{img | file = 3245DropCDome.jpg | width=170px}} |
''Note:'' Be careful not to press too hard and damage the ceiling tile | ''Note:'' Be careful not to press too hard and damage the ceiling tile | ||
Latest revision as of 08:41, 10 May 2022
Mount the Camera
Drywall mounting instructions
- Using a stud finder, scan the mount location to ensure the camera is not mounted on a stud.
- Using a pencil, mark the four holes for the mount plate.
- Using a 3/16" drill bit, drill the marked locations and
- Install anchors and attach the mount plate using screws and washers.
- Using a hole saw or paddle bit, cut a hole centered in the wall plate where cables will pass through.
- Using the hole saw, drill a hole above the drop ceiling in line with the hole drilled where the camera is mounted.
- Cut two lengths of 22/2 long enough to reach the mounting location of the microphone.
- Using glow rods or fish tape, fish the network drop or patch cable in addition to the two sections of 22/2 audio cable through the drywall.
- Attach the camera the the mount plate
Drop Ceiling mount instructions
- If mounting to drop ceiling, determine where the camera will be located on the tile. Ensure that there will be clearance on the tile to secure the dome in place.
- Using two toggle bolts, secure the mount plate.
- Using a 1" paddle bit, drill a hole centered in the opening of wall plate. This is where cables will pass through.
- Cut two lengths of 22/2 long enough to reach the mounting location of the microphone.
- Using glow rods or fish tape, fish the network drop and 2 sections of 22/2 audio cable into the drop ceiling.
- Attach camera to mount plate.
-
Note: Be careful not to press too hard and damage the ceiling tile
