Difference between revisions of "Infrared (IR) Talkback"
IVSWikiBlue (talk | contribs) |
IVSWikiBlue (talk | contribs) (→IR Device mounting Instructions) |
||
| Line 19: | Line 19: | ||
#Wire the black and ground to the - and the red to the + of the AUDIO OUT of phoenix connector. | #Wire the black and ground to the - and the red to the + of the AUDIO OUT of phoenix connector. | ||
===IR Device mounting Instructions=== | ===IR Device mounting Instructions=== | ||
| − | #Run | + | #Determine the placement of the IR receiver. It will generally be best suited to be positioned in a corner. |
| + | #Remove the drop ceiling tile to which the IR receiver will be mounted | ||
| + | #:''Note:'' The IR receiver will be mounted as far back to the corner as space allows | ||
| + | #Run 22/2 cable to the IR T1. | ||
#Strip about an inch of white jacket off the 22/2, as well as about 1/2 inch of the colored jackets to expose the wire. | #Strip about an inch of white jacket off the 22/2, as well as about 1/2 inch of the colored jackets to expose the wire. | ||
| − | #Cut a 3.5mm cable | + | #Cut a 3.5mm audio cable (approx 12") and strip the jackets to expose the wires |
| + | #Splice the 3.5mm audio cable with the 22/2 with B-connectors. | ||
| + | #:[[File:Ir35mmSplice.JPG|link=https://ipivs.com/wiki/images/b/b9/Ir35mmSplice.JPG]] | ||
#Cover your splice with electrical tape. | #Cover your splice with electrical tape. | ||
#Plug the 3.5 cable into the Line In of the IR T1. | #Plug the 3.5 cable into the Line In of the IR T1. | ||
Revision as of 10:03, 7 May 2020
Contents
Required Parts and Tools
- Williams Talkback System IR T1
- Williams RX224 Receiver
- RDL 24V DC power supply
- 22/2 audio cable
- 18/2 low voltage cable
- B Connectors
- Fish Tape or Glow Rods
- Electrical Tape
- Wire Stripper
Installation Instructions
Connecting to the Camera
- Once the camera is installed, locate the AUDIO OUT on your camera
- Strip the jacket of the 22/2 cable revealing the red, black, and bare wires inside.
- Cut away the bare wire and plastic surround the cable inside. Strip away a small piece of the red and black jackets revealing the bare copper wire.
- Wire the black and ground to the - and the red to the + of the AUDIO OUT of phoenix connector.
IR Device mounting Instructions
- Determine the placement of the IR receiver. It will generally be best suited to be positioned in a corner.
- Remove the drop ceiling tile to which the IR receiver will be mounted
- Note: The IR receiver will be mounted as far back to the corner as space allows
- Run 22/2 cable to the IR T1.
- Strip about an inch of white jacket off the 22/2, as well as about 1/2 inch of the colored jackets to expose the wire.
- Cut a 3.5mm audio cable (approx 12") and strip the jackets to expose the wires
- Splice the 3.5mm audio cable with the 22/2 with B-connectors.
- Cover your splice with electrical tape.
- Plug the 3.5 cable into the Line In of the IR T1.
- Once audio is plugged in, locate your nearest power outlet to power the IR T1.
- Note: You may need to use 18/2 cable to add length to the power cable. Ensure that when splicing in the 18/2 to the power, that the red jacket of the 18/2 is spliced into the cable with the dashed white lines on the power supply.
- Ensure your IR T1 and RX224 are set to the same channel.
- Test the talkback unit is working by activating the talkback function within the VALT Software and having a partner to communicate with.
