Installing an Axis P3245 with a Louroe Verifact A Microphone

Required Parts and Tools

• Axis P3245-LV
• 3.5mm (Male to Male) Audio Cable
• Louroe Verifact A Microphone
• T20 Torx security bit
• Wire Stripper
• Wall Dogs (if mounting to concrete) (3/16")
• Screws and Anchors (3/16")
• Toggle bolts (If mounting to drop ceiling tile) (3/16")
• 1/2" paddle bit
• 3.5mm Audio Cable
• Toggle Bolts (for mic mount) (3/16")
• Drill bit and drill
• Phillips head drill bit or Phillips head screwdriver
• Small Flat head screwdriver
• Hole Saw (2")
• B Connectors
• Stud Finder
• Cat5/6 Patch Cable (7ft-15ft recommended)
• Shielded Stranded 22/2 + ground Wire
• Fish Tape or Glow Rods

Installation Instructions

Disassemble the Camera

1. Locate the network drop above the ceiling. It should be terminated with a male Ethernet end (service loop) or a biscuit jack. This line will have been ran back to the POE switch.

   Note: If the switch does not have POE, a POE injector will need to be installed at the network closet.

2. Using the T20 bit, remove the dome from the 3245.

   

3. Remove the camera from the mounting plate.

   

4. Determine the mount location of the 3245.

Mount the Camera

Drywall mounting instructions

1. Using a stud finder, ensure the mount location is free of being located on a stud.
2. Using a pencil, mark the four holes for the mount plate.
3. Using a 3/16" drill bit, drill the marked locations and
4. Install anchors and attach the mount plate using screws and washers.

   

5. Using a hole saw or paddle bit, cut a hole centered in the wall plate where cables will pass through.

   

6. Attach the camera the the mount plate

   

Drop Ceiling mount instructions

1. If mounting to drop ceiling, determine where the camera will be located on the tile. Ensure that there will be clearance on the tile to secure the dome in place.
2. Using two toggle bolts, secure the mount plate.

   

3. Using a 1" paddle bit, drill a hole centered in the opening of wall plate. This is where cables will pass through.

   

4. Attach camera to mount plate.

Note: Be careful not to press too hard and damage the ceiling tile

Connect Wiring

1. Connect patch cable into the Ethernet port on the Axis P3245.

   Note: When connected, activity will be visible on the link lights. If no link lights appear, ensure that POE is enabled on the POE switch and that the network drop is plugged in. After approximately one minute, all three LEDs should be green.

Aim the Camera

1. Manually aim the camera to the area of interest. This must be done before securing the dome.

Reassemble the Camera

1. Remove protective film before securing dome
2. Place the dome over on the camera. Using the T20 bit, tighten the dome cover in place.
3. Snap the Axis dome ring into the base plate

Connecting the Microphone

1. Strip the jacket off the 22/2, revealing the red, black, and common (bare wire) on both sides of the cable.
2. Remove the string and plastic casings covering the red and black cables.
3. Strip the red and black jackets off the wire exposing the copper. Cut copper evenly on both ends. Remove ground.
4. At the Verifact A, connect the power cable to ports A and C. Connect the audio cable to ports B and C.

   

Wiring Diagram

Select Optional Second Camera

Axis P3235

Axis P3245

Axis P3364/P3365

Axis P3374/P3375

Axis Axis F41

Axis P5414/P5415

Axis Axis M5525

Axis Axis P5635

Axis P5655

Axis V5914/V5915

Axis Q8414