Difference between revisions of "Speaker Selector Configuration"
IVSWikiBlue (talk | contribs) (→Creating a Canvas User Interface) |
IVSWikiBlue (talk | contribs) (→Tesira Software) |
||
| (21 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
=Description/Objective= | =Description/Objective= | ||
| − | This is an example with a Control Room Audio Solution in a nursing sim lab. In this example, there are two speakers in the sim room | + | This is an example with a Control Room Audio Solution in a nursing sim lab. In this example, there are two speakers in the sim room; an overhead speaker for communication and instructions, and a PSP in-wall speaker to communicate as the dummy patient. The customer is requesting a User Interface to select the speaker for their talkback audio at a moment's notice. This means we will also build a Canvas User Interface (this will be covered in another section). Before building in Canvas, it is crucial to create the Tesira configuration properly. |
| − | |||
=Physical Wiring/Line Diagram= | =Physical Wiring/Line Diagram= | ||
Below is the physical wiring diagram. | Below is the physical wiring diagram. | ||
| − | + | {{img | file = CRAS_Speaker_Selector_Line_Diagram.png | width=800px}} | |
=Tesira Software= | =Tesira Software= | ||
==Connections== | ==Connections== | ||
| − | # If | + | # If the physical connections are complete, open the Tesira software and start building a configuration. |
| − | # In this configuration | + | # In this configuration use the following blocks: |
#* TesiraFORTE CI block | #* TesiraFORTE CI block | ||
#* Peak Meter x 3 | #* Peak Meter x 3 | ||
| Line 19: | Line 18: | ||
#* Compressor with "ganged mode" and "advanced curve" | #* Compressor with "ganged mode" and "advanced curve" | ||
#* Matrix Mixer with 2 inputs and 5 outputs | #* Matrix Mixer with 2 inputs and 5 outputs | ||
| − | #* Standard Mixer with 2 inputs and 2 outputs | + | #* Standard Mixer with 2 inputs and 2 outputs (this will become the microphone selector in Canvas) |
| − | + | ||
#Connect the blocks as follows: | #Connect the blocks as follows: | ||
| − | #* Connect a peak meter to the Tesira Input block. This will help | + | #* Connect a peak meter to the Tesira Input block. This will help ensure proper levels are set on the preamp. |
#* Connect the AEC block to the Uber Filters, then the Filters to the Level Block. | #* Connect the AEC block to the Uber Filters, then the Filters to the Level Block. | ||
#* Connect the Level Block to the Compressor and the second Peak Meter. | #* Connect the Level Block to the Compressor and the second Peak Meter. | ||
#* Connect the Compressor to the Matrix Mixer. | #* Connect the Compressor to the Matrix Mixer. | ||
| − | |||
#* Connect outputs 1 & 2 from the Matrix Mixer to the Output block and peak meter. | #* Connect outputs 1 & 2 from the Matrix Mixer to the Output block and peak meter. | ||
#* Connect output 3 from the Matrix Mixer to the Standard Mixer. | #* Connect output 3 from the Matrix Mixer to the Standard Mixer. | ||
#* Connect the outputs from the Standard Mixer to the output block and the peak meter. | #* Connect the outputs from the Standard Mixer to the output block and the peak meter. | ||
#* Connect outputs 4 & 5 from the Matrix Mixer to the AEC Reference. | #* Connect outputs 4 & 5 from the Matrix Mixer to the AEC Reference. | ||
| − | |||
| + | # Matrix Mixer: The sim room mic will be sent to three places; the camera, the control room speaker, and the AEC reference for the push to talk mic. The push to talk mic will be sent 3 places; the camera, the Standard Mixer (renamed 'speaker selector' in this config), and the AEC reference for the room mic. | ||
| + | # The Standard Mixer sends the push to talk audio to two places; the overhead speaker and the PSP in-wall patient speaker. | ||
| − | When | + | When this is complete, the file should look something like this: |
| − | + | {{img | file = Tesira_Speaker_Selector_Config_3.png}} | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
==Creating a Canvas User Interface== | ==Creating a Canvas User Interface== | ||
| Line 51: | Line 41: | ||
In another section, we will build the corresponding Canvas UI configuration for the Speaker Selector. Click the image below: | In another section, we will build the corresponding Canvas UI configuration for the Speaker Selector. Click the image below: | ||
| − | + | {{img | file = Canvas_Section.png}} | |
==Processing Blocks in Tesira== | ==Processing Blocks in Tesira== | ||
| Line 57: | Line 47: | ||
For further insight about the other processing blocks and settings, refer back to the first configuration example, or click the image below: | For further insight about the other processing blocks and settings, refer back to the first configuration example, or click the image below: | ||
| − | + | {{img | file = Processing_Blocks_Page.png}} | |
==EQ and Compression== | ==EQ and Compression== | ||
For information on EQ settings, or click the image below: | For information on EQ settings, or click the image below: | ||
| − | + | ||
| + | {{img | file = EQ_Page.png}} | ||
For Compression parameters, click the image below: | For Compression parameters, click the image below: | ||
| − | + | ||
| + | {{img | file = Compression_Page.png}} | ||
Latest revision as of 10:43, 10 May 2022
Contents
Description/Objective
This is an example with a Control Room Audio Solution in a nursing sim lab. In this example, there are two speakers in the sim room; an overhead speaker for communication and instructions, and a PSP in-wall speaker to communicate as the dummy patient. The customer is requesting a User Interface to select the speaker for their talkback audio at a moment's notice. This means we will also build a Canvas User Interface (this will be covered in another section). Before building in Canvas, it is crucial to create the Tesira configuration properly.
Physical Wiring/Line Diagram
Below is the physical wiring diagram.
Tesira Software
Connections
- If the physical connections are complete, open the Tesira software and start building a configuration.
- In this configuration use the following blocks:
- TesiraFORTE CI block
- Peak Meter x 3
- Uber Filter x 2
- Level Block with 2 ports
- Compressor with "ganged mode" and "advanced curve"
- Matrix Mixer with 2 inputs and 5 outputs
- Standard Mixer with 2 inputs and 2 outputs (this will become the microphone selector in Canvas)
- Connect the blocks as follows:
- Connect a peak meter to the Tesira Input block. This will help ensure proper levels are set on the preamp.
- Connect the AEC block to the Uber Filters, then the Filters to the Level Block.
- Connect the Level Block to the Compressor and the second Peak Meter.
- Connect the Compressor to the Matrix Mixer.
- Connect outputs 1 & 2 from the Matrix Mixer to the Output block and peak meter.
- Connect output 3 from the Matrix Mixer to the Standard Mixer.
- Connect the outputs from the Standard Mixer to the output block and the peak meter.
- Connect outputs 4 & 5 from the Matrix Mixer to the AEC Reference.
- Matrix Mixer: The sim room mic will be sent to three places; the camera, the control room speaker, and the AEC reference for the push to talk mic. The push to talk mic will be sent 3 places; the camera, the Standard Mixer (renamed 'speaker selector' in this config), and the AEC reference for the room mic.
- The Standard Mixer sends the push to talk audio to two places; the overhead speaker and the PSP in-wall patient speaker.
When this is complete, the file should look something like this:
Creating a Canvas User Interface
In another section, we will build the corresponding Canvas UI configuration for the Speaker Selector. Click the image below:
Processing Blocks in Tesira
For further insight about the other processing blocks and settings, refer back to the first configuration example, or click the image below:
EQ and Compression
For information on EQ settings, or click the image below:
For Compression parameters, click the image below:
